The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   The 1967 - 1972 Chevrolet & GMC Pickups Message Board (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=3)
-   -   Brake booster? (https://67-72chevytrucks.com/vboard/showthread.php?t=154644)

UncleRico 05-07-2005 06:19 PM

Brake booster?
 
Hi everyone. I'm pretty new to the board and to these trucks. Not the most knowledgebale guy so bare with me. Just bought a 69 shortbed 4x4 with a 350. The truck drives pretty good, but the brakes suck and it pulls hard to the right when I brake. I was told about a brake booster by the guy who sold it to me. Can anyone tell me more about this. What about the pulling when braking? Haven't looked at the drums yet, so I'm not sure what's going on in there.

Thanks for any help.

Cody

tmcgrawlookalike 05-07-2005 06:34 PM

could be the brakes(bad,adjusted differently,etc.)front end components(tie rod ends,idler arm,pitman arm,etc.)are brakes manual now?or power?was he just mentioning about the possibility of putting power(booster)on truck?it won`t cure pulling to one side,just make stopping better with less effort

john_doe 05-07-2005 07:24 PM

It wouldn't hurt to pull the drums just to inspect the brakes. Might just need shoes and/or brake parts.

special-K 05-07-2005 09:41 PM

Also,check for excessive play in the ball joints(6 & 12 o`clock),tie rods(3 & 9 o`clock),and bearings(knuckles firm/hubs move,3 & 9,6 & 12,whatever).

Americanrider 05-08-2005 03:51 AM

My truck was doing the same thing, and it does not have a booster. When I pulled the r/f drum, what was left of the lower spring that holds the bottom of the two shoes together fell out, $1.25 for the spring, $16.90 to get the drums turned and back to stopping in a straight line. ;)

junkyard truck 05-08-2005 09:13 AM

Brakes
 
Hey, The 1st thing you need to do is check and repair all 4 brakes. It might be simply, just adjusting or bleeding, or maybe a total brake job, but safety 1st, you don't want to bend up your truck and if you have my luck that's what would happen to me because I couldn't stop when I needed to. Good luck, Larry

UncleRico 05-08-2005 09:31 PM

booster?
 
Thanks guys. Sorry about the confusion in my orginal post. I'm planning on pulling things apart this week and redoing the brakes. As far as the booster goes...I don't have one installed but heard that I can add one to my existing system??? I think the extra braking power is needed as it's not quite as strong as I'd like. Where would I find one? I've tried searching for it in various places on the net but don't know exactly what I'm looking for so I haven't found it.

Thanks,

Cody

Dick Dale 05-09-2005 08:11 AM

A Power Booster gives you power brakes and not more brake power, it just makes it easier to push the pedal down. It goes behind the master cylinder and you can get one at Auto Zone for about $90.

Ray_71Chev_in_PA 05-09-2005 08:47 AM

UncleRico,

I have a '77 Ford Bronco that demonstrated the 'pulled hard' to one side problem. The fault turned out to be the very last thing I could check: the flexible brake hose that goes out to, in my case, the caliper. They were both bad, in that they were no longer tube shaped inside. Once I replaced them, no more pull. I did what you are doing, a very comprehensive rebuild. It was just my luck that it was the last thing I looked at.

Ray

hotrodmtodd 05-09-2005 12:20 PM

The Basics
 
In general, braking systems work best when equal pressure is applied to both sides. If you have a vehicle that pulls to 1 side during braking, it generally means that either THAT side is working and the other side is not, or that THAT side is working incorrectly (too much or not releasing as it should) and the other side is OK. If any of you have bulldozers, you know this is how they STEER. Pull the right brake, and the machine steers right. Most of the time it will be a front brake issue to cause pulling. A grabbing rear brake (and front obviously) will skid in gravel to let you know. Most common causes of brake related pulling are: uneven drum adjustment (f or r), a caliper sticking in the out position or an internally collapsed brake hose (same thing happens to your straw when your milkshake is too thick) May sound stupid, but true. If you cut a brake hose in a cross-section, you will see the 2 layers, which will seperate with age. Take my advice on this one, spend the money when it comes to brakes, that dress-up stuff can wait another week. Take care, Hot Rod

UncleRico 05-10-2005 02:38 AM

Thanks guys. Looking into it this weekend.

Cody

ale8oneboy 05-10-2005 01:15 PM

Still living in 1982 ? If ya are, a 82 front end will bolt under that 69' Becareful with that meat. Gosh!

UncleRico 05-10-2005 04:16 PM

Napoleon rocks
 
ale8one...wanna see my movie?

Gotta love Naploeon. It's pretty much the worst movie ever made

ale8oneboy 05-11-2005 12:26 PM

Yeah, my brother agrees. He said I wasted over an hour of his life. Makes me feel good now, since i've seen it like 4 times. But he thinks the Time Machine/Nut Shocker is funny.. Where did ya find the image?


All times are GMT -4. The time now is 06:39 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright 1997-2025 67-72chevytrucks.com