The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   The 1967 - 1972 Chevrolet & GMC Pickups Message Board (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=3)
-   -   Need help....Motor mounts not lining up??? (https://67-72chevytrucks.com/vboard/showthread.php?t=658264)

aod92 01-29-2015 09:57 PM

Need help....Motor mounts not lining up???
 
Here's a couple of pics of what I'm dealing with. I'm trying to mock up my motor but the holes aren't lining up. Ece ls swap mounts going into a 67 that originally had an I6 motor. With these mounts I'm supposed to drill one hole in the cross member. When I line up the one bottom hole the mount sits too high from the top of the frame. I'm completely lost here. Your help is appreciated!
http://i58.tinypic.com/2j1tzs1.jpg
http://i62.tinypic.com/2qs5tme.jpg

Ironangel 01-30-2015 12:42 AM

Re: Need help....Motor mounts not lining up???
 
Think I would email some these pics and verify all the info with ECE to make sure those are in fact the correct mounts. I would also try fitting them to the motor then lower them with the motor/tranny/drive line (if you have it) to see where your at...Might get lucky and have to drill three holes instead of one...?

LockDoc 01-30-2015 12:53 AM

Re: Need help....Motor mounts not lining up???
 
-
Those are '73 & up mounts. They are not a direct bolt in.

LockDoc

aod92 01-30-2015 12:57 AM

Re: Need help....Motor mounts not lining up???
 
Quote:

Originally Posted by LockDoc (Post 7025975)
-
Those are '73 & up mounts. They are not a direct bolt in.

LockDoc

I bought them off of a guy who had them on his 68. He said they bolted right up. Would I be fine notching the frame to get the top bolts to line up?

LockDoc 01-30-2015 01:03 AM

Re: Need help....Motor mounts not lining up???
 
Here is a couple of threads on the subject....

http://67-72chevytrucks.com/vboard/s...d.php?t=128765

http://67-72chevytrucks.com/vboard/s...d.php?t=366800

LockDoc

aod92 01-30-2015 01:12 AM

Re: Need help....Motor mounts not lining up???
 
Quote:

Originally Posted by LockDoc (Post 7025986)

Thank you for the links, but I'm still a bit confused. The brackets I have seem to tall and those links don't address that problem.

LockDoc 01-30-2015 01:19 AM

Re: Need help....Motor mounts not lining up???
 
Quote:

Originally Posted by aod92 (Post 7025992)
Thank you for the links, but I'm still a bit confused. The brackets I have seem to tall and those links don't address that problem.


I have never used them. The only truck I have seen with them in cut a notch out of the frame so the top holes would line up and re-drilled the bottom holes in the cross member to match the mounts. I think he only used one bolt in the bottom.

LockDoc
.

aod92 01-30-2015 01:21 AM

Re: Need help....Motor mounts not lining up???
 
Quote:

Originally Posted by LockDoc (Post 7026001)
I have never used them. The only truck I have seen with them in cut a notch out of the frame so the top holes would line up and re-drilled the bottom holes in the cross member to match the mounts. I think he only used one bolt in the bottom.

LockDoc
.

Ok, that's what I was thinking I would have to do. Thanks for your help.

LockDoc 01-30-2015 01:24 AM

Re: Need help....Motor mounts not lining up???
 
Quote:

Originally Posted by aod92 (Post 7026004)
Ok, that's what I was thinking I would have to do. Thanks for your help.

No problem.

LockDoc


All times are GMT -4. The time now is 01:13 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright 1997-2025 67-72chevytrucks.com