Power Brake Conversion Problem - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**rharris** · 06-16-2018, 11:05 AM

I added power brakes to my 72 c10. I have a new MC for power brake setup, a factory bracket, pushrod, and booster. I have read that the pedal will be somewhat closer to the floor board with the power setup, so that didn't surprise me (only 1 hole in brake pedal). However, the brakes feel harder than manual. They bled up fine, and I bench bled the MC and i do not have a brake warning light. If I step on the brakes while running, the rpm's die off very noticeably. After shutting off the engine, I can hear hissing for a few seconds. Could a faulty booster be the problems? The brakes seem to work the same with the vacuum line pulled off the booster.

**Steeveedee** · 06-16-2018, 12:48 PM

Yup, sounds like a vacuum leak. You should not hear any hissing.

**The Rocknrod** · 06-16-2018, 01:23 PM

Vacuum leak.

**rharris** · 06-16-2018, 08:31 PM

i assume with the engine dying when pushing the brake peddle it would point to the booster. The manifold fitting and vacuum tube are new. I also noticed that when I shift into gear it has a lag time. Guessing that is due to the leaky diaphragm in booster.

**rharris** · 06-22-2018, 05:58 PM

Thanks fellas, new booster came today - works much better. Brakes seem to grab all at once but they work much better. Maybe some adjusting this weekend.

06-16-2018, 11:05 AM	#1
rharris Senior Member Join Date: Apr 2013 Location: Pottsgrove PA Posts: 560	Power Brake Conversion Problem I added power brakes to my 72 c10. I have a new MC for power brake setup, a factory bracket, pushrod, and booster. I have read that the pedal will be somewhat closer to the floor board with the power setup, so that didn't surprise me (only 1 hole in brake pedal). However, the brakes feel harder than manual. They bled up fine, and I bench bled the MC and i do not have a brake warning light. If I step on the brakes while running, the rpm's die off very noticeably. After shutting off the engine, I can hear hissing for a few seconds. Could a faulty booster be the problems? The brakes seem to work the same with the vacuum line pulled off the booster. __________________ 72 Cheyenne Super C10 SWB 2001 Silverado 1500HD Crew 2011 Silverado 2500HD Crew Duramax (Hers) Last edited by rharris; 06-16-2018 at 12:16 PM.

06-16-2018, 12:48 PM	#2
Steeveedee Who Changed This? Join Date: Jan 2013 Location: Simi Valley, CA Posts: 10,934	Re: Power Brake Conversion Problem Yup, sounds like a vacuum leak. You should not hear any hissing. __________________ ~Steven '70 Chevy 3/4T Longhorn CST 402/400/3.56 Custom Camper Simi Valley, CA

06-16-2018, 01:23 PM	#3
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: Power Brake Conversion Problem Vacuum leak. __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

06-16-2018, 08:31 PM	#4
rharris Senior Member Join Date: Apr 2013 Location: Pottsgrove PA Posts: 560	Re: Power Brake Conversion Problem i assume with the engine dying when pushing the brake peddle it would point to the booster. The manifold fitting and vacuum tube are new. I also noticed that when I shift into gear it has a lag time. Guessing that is due to the leaky diaphragm in booster. __________________ 72 Cheyenne Super C10 SWB 2001 Silverado 1500HD Crew 2011 Silverado 2500HD Crew Duramax (Hers)

06-22-2018, 05:58 PM	#5
rharris Senior Member Join Date: Apr 2013 Location: Pottsgrove PA Posts: 560	Re: Power Brake Conversion Problem Thanks fellas, new booster came today - works much better. Brakes seem to grab all at once but they work much better. Maybe some adjusting this weekend. __________________ 72 Cheyenne Super C10 SWB 2001 Silverado 1500HD Crew 2011 Silverado 2500HD Crew Duramax (Hers)



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.