|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
04-19-2004, 12:14 PM
|
#1 |
|
Registered User
Join Date: Sep 2003
Location: Atascadero, CA.
Posts: 149
|
need advice on how to remove springs
my delima is how do I lift the frame safely to remove the springs in the rear and front. The frame is about 32inches on its lowest point. Any recomendations on how to lift the frame?
|
|
|
|
04-19-2004, 08:55 PM
|
#2 |
|
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Forklift???
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
|
|
|
|
04-19-2004, 09:59 PM
|
#3 |
|
Registered User
Join Date: Sep 2003
Location: Atascadero, CA.
Posts: 149
|
no one rents those around here
__________________
84 Silverado, |
|
|
|
|
04-20-2004, 02:33 AM
|
#4 |
|
Registered User
Join Date: Apr 2001
Location: jefferson city, mo
Posts: 1,364
|
we built custom jack stands for my buddies truck, he has about 14 inches of lift with 39 inch tires, we also put smaller tires on it when it goes in the shop which lowers it quite abit.
|
|
|
|
|
04-20-2004, 01:56 PM
|
#5 |
|
Senior Member
Join Date: Apr 2004
Location: sw colorado
Posts: 2,720
|
when i lifted my truckwe used a bumper jack and some 20 ton jack stands. you could probably use a cherry picker on the back but i think the front would be to heavy.
Ryan |
|
|
|
|
04-20-2004, 09:23 PM
|
#6 |
|
Registered User
Join Date: Sep 2003
Location: Atascadero, CA.
Posts: 149
|
would removing both tires in the back lowering the frame on to 3 ton jack stands sitting on top of two cinderblocks work?
__________________
84 Silverado, |
|
|
|
|
04-21-2004, 05:53 AM
|
#7 |
|
Registered User
Join Date: Apr 2001
Location: jefferson city, mo
Posts: 1,364
|
fug no, cinder blocks are weak, why not get some steel and build bigger jack stands. put a jack under the axle, lift it off the ground, take off the tires, lower the jack till you can put jack stands under, youll need the jack under the axle any way to relieve the pressure off the springs from all the weight hanging down. Dont use cinder blocks, you can break a cinder block by dropping it, you wanna crawl under a 5000 pound truck held up by these?
|
|
|
|
|
04-21-2004, 06:39 AM
|
#8 |
|
user # 2756
 
Join Date: Jun 2001
Location: Chesapeake, Virginia
Posts: 4,612
|
Pic please. I recommend jacking up the front or rear and removing the tires then get some tall jack stands under the frame. 32" to the bottom of the frame that's tall. Do one end first.
http://67-72chevytrucks.com/vboard/s...threadid=97507
__________________
1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm 
|
|
|
|
|
04-21-2004, 11:23 AM
|
#9 |
|
Registered User
Join Date: Sep 2003
Location: Atascadero, CA.
Posts: 149
|
yup, thats what I was thinking, Thanks everyone
__________________
84 Silverado, |
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
