Lower A-arm question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Bowtie468** · 12-30-2004, 11:02 AM

Guys, once i bolt my lower a-arms back onto the crossmember, what is the best way to check that my cross-shaft is properly positioned (side to side) on the a-arm. Before i bolted them up, i roughly centered the shaft between the caps.
I just want to make sure i'm not 1 turn off or so before i button everything up.

Thanks !!!

Chris

**Bowtie468** · 12-30-2004, 02:53 PM

This may help explain the question ! Is there some measurement i can take between the crossmember and the cap? I understand that the cross-shaft is located in place by means of the dimple, yet rotating the shaft will cause the a-arm to move forward or rearward. This would directly affect caster, wouldn't it ?? This is what i am trying to properly position before installing springs and spindles.

**lolife99** · 12-30-2004, 04:36 PM

There is a "shoulder" on the inside of the cross shaft. I just made sure the "shoulder" was the same distance (from the inside edge of the control arm) on both sides.

crazy longhorn · 12-30-2004, 05:19 PM

Its been a while since i did mine, so "bear with me" . if you run one of the bushings all the way tight in the arm, then scew the shaft in , till it stops....back it off 1 full turn(or till the locator hole is in the right spot for the pin on the crossmember). then screw the other bushing in, & down tight.....you should be pretty close. you can check this , by turning the shaft to bottom , against both ends, to find the center. after you are set, the scerws on the shaft /bushings wont move you too much.....just remember "center" as best you can, & the bottom arm is located with a pin. After that, its up to the alingment "dude"

Best of luck,crazyL

SCOTI · 12-30-2004, 05:39 PM

There should be a 'dowel' pin on the bottom of each front u-bolt mount that locates the shaft in the proper position. The trick is to align the 'dowel' w/the 'notch' in the shaft while aligning/tightening the u-bolts.

Looking @ the lower a-arm shaft you should see the notch (recess). If you look under your truck & you should see the 'dowel' as they're the same dimensions. Once they're tightened together, the arm is located correctly & the measurement won't change when pivoting the a-arm.

**Bowtie468** · 12-30-2004, 08:29 PM

Sweet.. Thanks for all the valuable info guys !! Putting on the drop spindles as i type this

Many Thanks !!

Chris

12-30-2004, 11:02 AM	#1
Bowtie468 Senior Member Join Date: Jun 2002 Location: Cecilia, Louisiana Posts: 1,638	Lower A-arm question Guys, once i bolt my lower a-arms back onto the crossmember, what is the best way to check that my cross-shaft is properly positioned (side to side) on the a-arm. Before i bolted them up, i roughly centered the shaft between the caps. I just want to make sure i'm not 1 turn off or so before i button everything up. Thanks !!! Chris __________________ Chris click here to see my buildpage http://67-72chevytrucks.com/vboard/s...d.php?t=394656 ---------------------------------- 1979 C10 Silverado Big10 SWB Factory 454/400 Cardinal Red/Santa Fe Tan (original paint) 1969 Camaro X44 LS swap 1968 C10 SWB Fleetside (SOLD) 468BBC MultiPort TPI / Dynamic EFI P4 Black/Black 1963 Nova SS convertible (SOLD) 194 I6/ PowerGlide

12-30-2004, 02:53 PM	#2
Bowtie468 Senior Member Join Date: Jun 2002 Location: Cecilia, Louisiana Posts: 1,638	This may help explain the question ! Is there some measurement i can take between the crossmember and the cap? I understand that the cross-shaft is located in place by means of the dimple, yet rotating the shaft will cause the a-arm to move forward or rearward. This would directly affect caster, wouldn't it ?? This is what i am trying to properly position before installing springs and spindles. __________________ Chris click here to see my buildpage http://67-72chevytrucks.com/vboard/s...d.php?t=394656 ---------------------------------- 1979 C10 Silverado Big10 SWB Factory 454/400 Cardinal Red/Santa Fe Tan (original paint) 1969 Camaro X44 LS swap 1968 C10 SWB Fleetside (SOLD) 468BBC MultiPort TPI / Dynamic EFI P4 Black/Black 1963 Nova SS convertible (SOLD) 194 I6/ PowerGlide Last edited by Bowtie468; 12-23-2005 at 06:27 PM.

12-30-2004, 04:36 PM	#3
lolife99 67-72 parts collector,… Join Date: Nov 2002 Location: Mid-MO Posts: 22,700	There is a "shoulder" on the inside of the cross shaft. I just made sure the "shoulder" was the same distance (from the inside edge of the control arm) on both sides. __________________ Keith Convert to disc brakes. http://67-72chevytrucks.com/vboard/s...d.php?t=444823

12-30-2004, 05:19 PM	#4
crazy longhorn Fabricate till you "puke" Join Date: Jun 2002 Location: Ill Posts: 9,402	Its been a while since i did mine, so "bear with me" . if you run one of the bushings all the way tight in the arm, then scew the shaft in , till it stops....back it off 1 full turn(or till the locator hole is in the right spot for the pin on the crossmember). then screw the other bushing in, & down tight.....you should be pretty close. you can check this , by turning the shaft to bottom , against both ends, to find the center. after you are set, the scerws on the shaft /bushings wont move you too much.....just remember "center" as best you can, & the bottom arm is located with a pin. After that, its up to the alingment "dude" Best of luck,crazyL __________________ 69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears....

12-30-2004, 05:39 PM	#5
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,066	There should be a 'dowel' pin on the bottom of each front u-bolt mount that locates the shaft in the proper position. The trick is to align the 'dowel' w/the 'notch' in the shaft while aligning/tightening the u-bolts. Looking @ the lower a-arm shaft you should see the notch (recess). If you look under your truck & you should see the 'dowel' as they're the same dimensions. Once they're tightened together, the arm is located correctly & the measurement won't change when pivoting the a-arm. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.* Last edited by SCOTI; 12-30-2004 at 06:09 PM.

12-30-2004, 08:29 PM	#6
Bowtie468 Senior Member Join Date: Jun 2002 Location: Cecilia, Louisiana Posts: 1,638	Sweet.. Thanks for all the valuable info guys !! Putting on the drop spindles as i type this Many Thanks !! Chris __________________ Chris click here to see my buildpage http://67-72chevytrucks.com/vboard/s...d.php?t=394656 ---------------------------------- 1979 C10 Silverado Big10 SWB Factory 454/400 Cardinal Red/Santa Fe Tan (original paint) 1969 Camaro X44 LS swap 1968 C10 SWB Fleetside (SOLD) 468BBC MultiPort TPI / Dynamic EFI P4 Black/Black 1963 Nova SS convertible (SOLD) 194 I6/ PowerGlide

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.