72' Suburban VS. 72' Truck Suspension? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

PrimeredThunder · 10-13-2006, 01:36 PM

OK, I had a 72' 1/2-Ton SWB that had rear coils that I bagged a couple years ago. Now that truck is gone and I've Aqquired a 72' 1/2-TOn Suburban with Coils that I want to bag'.

Question is; are there, if any, differences between the suspensions on both trucks? As for when I order brackets are they any different?

Also, I ran Firestone #2600 bags in front and #2500 in back on the SWB truck, should I look to run a different bag on the Suburban? (Dont plan on towing).

Last Question-I am planning on going with ART brackets, Suicide-Doors for bags/valves etc, ECE for a track-bar kit, and then a CPP C-notch.

Is there any new compnies out there making anything else I would need to get the Suburban closer to the ground?

Any Help is appreciated guys! Thanks!

Kenny

*Shane* · 10-13-2006, 04:34 PM

be careful mixing that ECE track bar and CPP's notch kit ... you will either need to run at least a 1 1/2" lowering block ... or mod the C-Notch.

See this thread - http://67-72chevytrucks.com/vboard/s...d.php?t=208563

I just went thru this and ended up using the 1 1/2" lowering block from CPP. Also, the C-Notch will require some mods, as well as the chassis, where the bag mounts if you happen to use the older style Firestone bags with the studs, as opposed to the tapped holes.

See this thread - http://67-72chevytrucks.com/vboard/s...d.php?t=212757

Hope this helps.

10-13-2006, 01:36 PM	#1
PrimeredThunder Back from the Dead Join Date: Dec 2001 Location: Salem, Oregon Posts: 522	72' Suburban VS. 72' Truck Suspension? OK, I had a 72' 1/2-Ton SWB that had rear coils that I bagged a couple years ago. Now that truck is gone and I've Aqquired a 72' 1/2-TOn Suburban with Coils that I want to bag'. Question is; are there, if any, differences between the suspensions on both trucks? As for when I order brackets are they any different? Also, I ran Firestone #2600 bags in front and #2500 in back on the SWB truck, should I look to run a different bag on the Suburban? (Dont plan on towing). Last Question-I am planning on going with ART brackets, Suicide-Doors for bags/valves etc, ECE for a track-bar kit, and then a CPP C-notch. Is there any new compnies out there making anything else I would need to get the Suburban closer to the ground? Any Help is appreciated guys! Thanks! Kenny __________________ The only Carb that matters to me is the one under my hood! Salem, Oregon

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

10-13-2006, 04:34 PM	#2
Shane Account Suspended Join Date: Jun 2000 Location: over yonder Posts: 14,270	Re: 72' Suburban VS. 72' Truck Suspension? be careful mixing that ECE track bar and CPP's notch kit ... you will either need to run at least a 1 1/2" lowering block ... or mod the C-Notch. See this thread - http://67-72chevytrucks.com/vboard/s...d.php?t=208563 I just went thru this and ended up using the 1 1/2" lowering block from CPP. Also, the C-Notch will require some mods, as well as the chassis, where the bag mounts if you happen to use the older style Firestone bags with the studs, as opposed to the tapped holes. See this thread - http://67-72chevytrucks.com/vboard/s...d.php?t=212757 Hope this helps.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.