|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
08-27-2002, 04:01 PM
|
#1 |
|
Registered User
Join Date: Mar 2002
Location: Bondurant, IA but in Worcester, MA for school
Posts: 767
|
Parts I need to convert to HEI??
Could some of you please list the parts that I would need from a catalog like Jegs or Summit to convert to HEI? Please list all and I mean all the parts that I would need. This would be very helpful. THanks a lot guys.
HotRod
__________________
1970 Chevy C-20 350 V-8 Turbo 350 w/ shift kit Dana 60 w/ 4.10 gears AND Powr-Loc POSI New Additions: Summit Headers 135amp alternator Proform HEI Edelbrock 1406 600cfm carb Sunpro Tach Powr-Loc POSI Edelbrock Performer RPM Intake MSD 6A Ignition Box AIM: HotRod929 Visit My Site: http://1970chevy.netfirms.com/ |
|
|
|
08-27-2002, 05:36 PM
|
#2 |
|
Psycho-billy Member
Join Date: Jul 2001
Location: about 40 miles west of Cleveland, Ohio
Posts: 2,591
|
you will need the HEI distributor, HEI plug wires, some wire (10ga) and two spade (female) connectors.......that's all.
Might want to change the plugs (gapped .040-.045) while you're in there. If the ones that you have are new, make sure you re-gap them to the above specs.
__________________
'72 C-10 350 w/Lunati Voodoo cam (207*/213*, .437/.454), Performer intake, 625 Road Demon Jr. and Hooker headers. Support your community, support yourself. Buy local, buy American  (or Canadian).
Last edited by lux hauler; 08-27-2002 at 05:41 PM. |
|
|
|
|
08-27-2002, 06:10 PM
|
#3 |
|
Registered User
Join Date: Mar 2002
Location: Bondurant, IA but in Worcester, MA for school
Posts: 767
|
Any recomendations as to what make of HEI distributor I should get? I see so many in the summit and Jegs catalogs that I dont know which one to get. Thanks
HotRod
__________________
1970 Chevy C-20 350 V-8 Turbo 350 w/ shift kit Dana 60 w/ 4.10 gears AND Powr-Loc POSI New Additions: Summit Headers 135amp alternator Proform HEI Edelbrock 1406 600cfm carb Sunpro Tach Powr-Loc POSI Edelbrock Performer RPM Intake MSD 6A Ignition Box AIM: HotRod929 Visit My Site: http://1970chevy.netfirms.com/ |
|
|
|
|
08-27-2002, 06:45 PM
|
#4 |
|
Registered User
Join Date: Apr 2001
Location: Fallon, NV
Posts: 24
|
Better do the altenator upgrade while you are in there, you will sure to be popping MODULES if you dont.
|
|
|
|
|
08-27-2002, 09:55 PM
|
#5 | |
|
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,690
|
Quote:
I would not bother with a brand new one. They cost alot of money, and you can save about 2/3 of that by getting a late '70's distributor out of a junk yard. Prices range from 10 bucks, to about 60. I would be hard pressed to pay more than 40 myself. Then clean it, replace the module and coil, get a new cap and rotor, and the aformentioned wires. This set up will more likely than not last just as long as a jegs or summit unit, and if/when you do need parts, you can get parts from any parts store across the nation. just tell them it is off of a '7-what ever Chevy Jalopie SS...or what ever it came from. Just my opinion. |
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
