Rocker replacement help please!! - The 1947 - Present Chevrolet & GMC Truck Message Board Network

jmedero · 01-17-2009, 11:11 PM

Ok so I tore into it today and have some questions. How does the inner rocker line up? There is a part of the inner rocker that the weather strip goes on right? If so when I line up the rocker to it this way the rocker looks to high. If I lower it where the top of the inner rocker lines up flush with the floor pan then no place to attach weather strip. I took some picks of the diff set ups.. can someone tell me which one is right. Thanks in advance. My bloody knuckles will thank you.

jmedero · 01-17-2009, 11:13 PM

some more pics...

*LILRED66* · 01-17-2009, 11:41 PM

The door seal attaches to the lip on the rocker panel and the bottom edge of the inner rocker panel lays flat on the bottom flange of the outer rocker.

jmedero · 01-18-2009, 01:12 AM

so it should look like pictures 2, 3, and 4 when put on. I am just confused bc the lip for the weather strip on the rocker makes the weather strip mount slide on the edge of the rocker not the inner rocker right? Can I get a picture of what this looks like on a truck? The lower door jamb that is with the area were the strip mounts to.

Thanks

Alan's Classic · 01-18-2009, 01:18 AM

The weatherstrip attaches to the outer rocker lip. hope the pix help

jmedero · 01-18-2009, 01:54 AM

Thanks for the pic's they helped a bunch. Now I see what it should look like. Mine was so rusted that the whole area was covered with bondo so I had no starting point. ON the inner rocker it has one hole drilled out on either end. On the support comming down from the A pillar it has 3 holes. From what I messured the one hole on the inner lines up with the middle hole on the support right?

This is the hole I am speaking about.

Alan's Classic · 01-18-2009, 02:00 AM

Sorry I can't answer that one. I only used the back portion of that piece (inner rocker). My front floor pan had a section of inner rocker with it.

TimE · 01-31-2009, 03:54 PM

How's this coming along for you Juan? Just wondering, I've got the same fun ahead for me.

jmedero · 01-31-2009, 07:14 PM

well today I blasted the area and cut some more rot out. I have fitted it all in and will be welding it this week. I got some pics and will post once I get some welding done. What I had some issues fig out was that there is a small gap between the floor and the outer rocker. I thought it welded up flush with the floor board. I saw one driving around and stoped him to look. It has a small area for wires and the weather strip to run in. I was trying to make it all flush.... and it was not going to work that way. I will post pics soon.... and thanks for asking!!

TimE · 01-31-2009, 07:53 PM

Keep us posted!!

Alan's Classic · 03-21-2009, 10:30 PM

Any updates??

01-17-2009, 11:11 PM	#1
jmedero Registered User Join Date: Jun 2008 Location: pensacola fl Posts: 3,073	Rocker replacement help please!! Ok so I tore into it today and have some questions. How does the inner rocker line up? There is a part of the inner rocker that the weather strip goes on right? If so when I line up the rocker to it this way the rocker looks to high. If I lower it where the top of the inner rocker lines up flush with the floor pan then no place to attach weather strip. I took some picks of the diff set ups.. can someone tell me which one is right. Thanks in advance. My bloody knuckles will thank you. Attached Images

01-17-2009, 11:13 PM	#2
jmedero Registered User Join Date: Jun 2008 Location: pensacola fl Posts: 3,073	Re: Rocker replacement help please!! some more pics... Attached Images

01-17-2009, 11:41 PM	#3
LILRED66 Account Suspended Join Date: May 2005 Location: Kansas City, KS Posts: 3,906	Re: Rocker replacement help please!! The door seal attaches to the lip on the rocker panel and the bottom edge of the inner rocker panel lays flat on the bottom flange of the outer rocker.

01-18-2009, 01:12 AM	#4
jmedero Registered User Join Date: Jun 2008 Location: pensacola fl Posts: 3,073	Re: Rocker replacement help please!! so it should look like pictures 2, 3, and 4 when put on. I am just confused bc the lip for the weather strip on the rocker makes the weather strip mount slide on the edge of the rocker not the inner rocker right? Can I get a picture of what this looks like on a truck? The lower door jamb that is with the area were the strip mounts to. Thanks

01-18-2009, 01:18 AM	#5
Alan's Classic 1 thing at a time is progress. Join Date: Jun 2007 Location: Ball Ground GA Posts: 5,511	Re: Rocker replacement help please!! The weatherstrip attaches to the outer rocker lip. hope the pix help __________________ Alan Philippians 2:14-16 Alan's Classic Facebook page. North Georgia Group Project 1965 Vitamin C-10 1995 GMC Sierra K1500 The "Wrecker"

01-18-2009, 01:54 AM	#6
jmedero Registered User Join Date: Jun 2008 Location: pensacola fl Posts: 3,073	Re: Rocker replacement help please!! Thanks for the pic's they helped a bunch. Now I see what it should look like. Mine was so rusted that the whole area was covered with bondo so I had no starting point. ON the inner rocker it has one hole drilled out on either end. On the support comming down from the A pillar it has 3 holes. From what I messured the one hole on the inner lines up with the middle hole on the support right? This is the hole I am speaking about. Attached Images

01-18-2009, 02:00 AM	#7
Alan's Classic 1 thing at a time is progress. Join Date: Jun 2007 Location: Ball Ground GA Posts: 5,511	Re: Rocker replacement help please!! Sorry I can't answer that one. I only used the back portion of that piece (inner rocker). My front floor pan had a section of inner rocker with it. __________________ Alan Philippians 2:14-16 Alan's Classic Facebook page. North Georgia Group Project 1965 Vitamin C-10 1995 GMC Sierra K1500 The "Wrecker" Last edited by Alan's Classic; 01-18-2009 at 02:01 AM.

01-31-2009, 03:54 PM	#8
TimE Hey Y'all!! Join Date: Dec 2007 Location: Bay Minette, Alabama Posts: 1,755	Re: Rocker replacement help please!! How's this coming along for you Juan? Just wondering, I've got the same fun ahead for me. __________________ Just hopin' I live long enough to finish something!!!

01-31-2009, 07:14 PM	#9
jmedero Registered User Join Date: Jun 2008 Location: pensacola fl Posts: 3,073	Re: Rocker replacement help please!! well today I blasted the area and cut some more rot out. I have fitted it all in and will be welding it this week. I got some pics and will post once I get some welding done. What I had some issues fig out was that there is a small gap between the floor and the outer rocker. I thought it welded up flush with the floor board. I saw one driving around and stoped him to look. It has a small area for wires and the weather strip to run in. I was trying to make it all flush.... and it was not going to work that way. I will post pics soon.... and thanks for asking!!

01-31-2009, 07:53 PM	#10
TimE Hey Y'all!! Join Date: Dec 2007 Location: Bay Minette, Alabama Posts: 1,755	Re: Rocker replacement help please!! Keep us posted!! __________________ Just hopin' I live long enough to finish something!!! Last edited by TimE; 01-31-2009 at 07:54 PM.

03-21-2009, 10:30 PM	#11
Alan's Classic 1 thing at a time is progress. Join Date: Jun 2007 Location: Ball Ground GA Posts: 5,511	Re: Rocker replacement help please!! Any updates?? __________________ Alan Philippians 2:14-16 Alan's Classic Facebook page. North Georgia Group Project 1965 Vitamin C-10 1995 GMC Sierra K1500 The "Wrecker"

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.