pics of backhalfs, 4-links, air bag setups

[sparkyhunt]

First I wanted to say this site is great, I've been searching through here for a few weeks. I have a '69 c-10 lwb that I want to make into a swb and have the body sit about an inch off the ground. I am on a budget and was wondering what the best way to do this will be?

[PBFAB.COM]

If you are a capable welder, the least expensive/best way to achieve what you're looking for would be a weld-in notch, and a four-link/air bag set-up. The factory trailing arms won't allow you to get down quite that low.

[BigShoe24]

Sparkyhunt,

You can find some good stuff through Porterbuilt & KP Components. I believe my entire truck is built from the two. Good Luck

[sparkyhunt]

I want to do a 4-link and air bag setup. I also want to raise the height of the floor in the bed so won't have the big hump in the middle. Would I be better off redoing the whole backhalf or doing the c-notch. I have not been able to find any pictures of anybody redoing the backhalf with a 4-link setup. If doing the c-notch is a better option, what would be the best way to re support the floor of the bed.

[PBFAB.COM]

Originally Posted by sparkyhunt

I want to do a 4-link and air bag setup. I also want to raise the height of the floor in the bed so won't have the big hump in the middle. Would I be better off redoing the whole backhalf or doing the c-notch. I have not been able to find any pictures of anybody redoing the backhalf with a 4-link setup. If doing the c-notch is a better option, what would be the best way to re support the floor of the bed.

The hard part about all this, is that there's so many ways to accomplish the end result. With that being said, the multiple options will all have advantages and disadvantes... you'll just have to decide where you want to compromise. The least expensive/best route would be the weld-in notch and a four-link with a long panhard bar, sleeved bags mounted outside the rails over the axle.

A back-half will easily get it done, but it takes a lot more time and ability.

As for the bedfloor, just make some spacers to raise the bed floor supports to the desired height, and make a new flange where the floor can bolt in like the factory had it.

[sparkyhunt]

Originally Posted by porterbuilt

The hard part about all this, is that there's so many ways to accomplish the end result. With that being said, the multiple options will all have advantages and disadvantes... you'll just have to decide where you want to compromise. The least expensive/best route would be the weld-in notch and a four-link with a long panhard bar, sleeved bags mounted outside the rails over the axle.

A back-half will easily get it done, but it takes a lot more time and ability.

As for the bedfloor, just make some spacers to raise the bed floor supports to the desired height, and make a new flange where the floor can bolt in like the factory had it.

Any pictures of either setup, also what do you mean by sleeved bags? This will be my first time using air bags and want to do it right the first time. Thanks for pointing me in the right direction.

[Sweet 85 C10]

[ghettoluxury]

I have about 4 pages of photos here http://s211.photobucket.com/albums/b...frame%20shots/

[jmedero]

Nate this ones for you,
So what's the best rear set up for the most height? Meaning I am pitting the rear rails on the ground. I want to be able to get the most lift possible.

[PBFAB.COM]

Originally Posted by jmedero

Nate this ones for you,
So what's the best rear set up for the most height? Meaning I am pitting the rear rails on the ground. I want to be able to get the most lift possible.

In order to get the most lift, you need to run a double convoluted bag levered at around 1.5:1. That will get you in the 10"+ range. With that much lift, I would recommend a wishbone or a watt's link to locate the differential laterally. If you're looking for a kit, let me know and I can put something together for you, or help you find what you need! PM or e-mail me.

[PBFAB.COM]

Here's what we did with Dino's 66.

[BigShoe24]

I love that 66, is that the same truck thats now a crew?

[PBFAB.COM]

Originally Posted by BigShoe24

I love that 66, is that the same truck thats now a crew?

Yup... that was before its "Growth Spurt".

[gixxerpymp]

Any pics of the blue one with the bed on layed out?