|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
10-18-2009, 12:47 AM
|
#1 |
|
Registered User
Join Date: Mar 2004
Location: Hoytsville, Utah
Posts: 3,365
|
A couple rear suspension questions
Do I need to relocate my rear shocks if I drop 2.5 to 3 inches?
How much difference is there between 'HD rear coil springs' and normal, or non-HD coils? My Panel came with only 2 options, HD fronts and HD rears. I want to drop a little, but would like a little softer ride, too. I can't decide between a static drop or bags. As it is, even the 2 inch lip pulling into my shop will cause everything that's not bolted down to jump up into the air. It's almost like no spring at all, just a solid bar.
__________________
'68 Panel Project Boogie Chillin' '68 C-10 Ol' Green |
|
|
|
10-18-2009, 01:04 AM
|
#2 |
|
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,066
|
Re: A couple rear suspension questions
It's not necessary to relocate the shocks w/<3" drop but it wouldn't hurt either. You could do non-HD coils up front & bags in the rear for a compromise that allows the capacity of the HD springs w/the ride of the non-HD springs.
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
|
|
|
|
10-18-2009, 02:02 AM
|
#3 |
|
Registered User
Join Date: Mar 2004
Location: Hoytsville, Utah
Posts: 3,365
|
Re: A couple rear suspension questions
Thanks, SCOTI. I did go with standard coils in the front, with 2.5 drop spindles. If relocating the shocks, do I need to get special shocks? Oh-one more question-can I just use the lower shock relocator, or if I go that route do I need to relocate top and bottom? I really hate drilling out rivits.
__________________
'68 Panel Project Boogie Chillin' '68 C-10 Ol' Green Last edited by pritch; 10-18-2009 at 02:04 AM. |
|
|
|
|
10-18-2009, 02:07 AM
|
#4 | |
|
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,066
|
Re: A couple rear suspension questions
Quote:
http://www.67-72chevytrucks.com/vboa...d.php?t=359399 On mine, I get about 1.5" on each end that's modified. I would guess (educated @ that) the aftermarket would yield similar benefits.
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. Last edited by SCOTI; 10-18-2009 at 02:09 AM. |
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
