|
|
|
05-09-2010, 11:10 AM
|
#1 |
|
Registered Truck Offender
Join Date: May 2008
Location: hells training ground (aka Ariz)
Posts: 3,118
|
It's baaaaaaaack!
J-fab took a vacation in the middle of my header project so the 'about a week' became 'about a month'! But.. picked her up yesterday and she's back and I can start throwing some of this pile of parts together!
Jody did a beautiful job snaking the Headman Hustler weldup kit down through there. He fought with the Headman 'stub-flange' on the drivers side and decided to just whack the stubs off and make his own connection on the passengers side. Glad I wasted $170 on those stupid stub-flanges!! DOH! As always Jody's work is stellar! I just have to hang the mufflers and turnouts , fit them to the slip collar and then the headers will go to Affordable for coating. FINALLY,,, moving forward again.  
__________________
Still playin with trucks, even at my age! When you're dead, it's only a problem for the people around you, because you don't know you're dead. .....It's kinda the same when your STUPID. I just did my taxes and reviewed my SS statement. Thanks to the current administration it looks like I will only have to work till noon on the day of my funeral. |
|
|
|
05-09-2010, 11:58 AM
|
#2 |
|
Registered User
Join Date: Jan 2010
Location: nevada
Posts: 649
|
Re: It's baaaaaaaack!
nice work, very clean!
__________________
2003 Dodge 2500 1969 C10 2014 Camaro SS/RS/1LE |
|
|
|
|
05-09-2010, 01:03 PM
|
#3 |
|
Senior Member
Join Date: Apr 2000
Location: Delta,Pa
Posts: 14,948
|
Re: It's baaaaaaaack!
That looks good. Awesome job.
__________________
Owner of North Point Car Care in Dundalk Md. We specialize in custom exhaust on both modern and classic vehicles. We are a full service auto shop from classics to modern vehicles. Feel free to contact me with questions. I will give a 10% discount to any board member. |
|
|
|
|
05-09-2010, 02:29 PM
|
#4 |
|
Registered User
Join Date: Mar 2002
Location: Forney TX
Posts: 4,512
|
Re: It's baaaaaaaack!
Man I cant wait to hear this thing run. I just watched the pinks episode you were on again.
__________________
Troy 1965 Chevy Bagged,361 sbc,voodoo cam,1.5 full roller rockers,patriot 185cc vortec heads 2.02-1.60,vortec weiand polished intake,demon carb my truckhttp://67-72chevytrucks.com/vboard/s...d.php?t=332884 Big Red Dog build http://67-72chevytrucks.com/vboard/s...d.php?t=572274 |
|
|
|
|
05-09-2010, 11:55 PM
|
#5 | ||
|
60-66 Nut
  Join Date: Mar 2007
Location: Coeur d'Alene, Idaho
Posts: 23,252
|
Re: It's baaaaaaaack!
I agree....
Quote:
Quote:
__________________
Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE |
||
|
|
|
|
05-09-2010, 09:03 PM
|
#6 |
|
Right on the line, baby!
Join Date: Oct 2003
Location: Phila, PA 19130
Posts: 1,486
|
Re: It's baaaaaaaack!
And again.
__________________
83 GMC 406 th400/3.73 Eaton Truetrac posi, headers, x pipe, & racePros. Tubular control arms, lowering rear springs, caltracs. Still ugly, but getting built right, although slowly Click and scroll down for site vendors! Subscribe here! |
|
|
|
|
05-09-2010, 11:18 PM
|
#7 |
|
ShortBus KingPin
Join Date: Feb 2010
Location: houston texas
Posts: 146
|
Re: It's baaaaaaaack!
What is the primary diameter? 1 7/8?
__________________
67 shortstep prosteet. 505 BBC, FULL BILLET TH350, Owner built EVERYTHING.... (My RIDE) 2008 GMC Yukon DENALI, 425 AWHP, 5700LBS, 12.40's at 109mph. (Her RIDE) 2006 Kawasaki Brute Force, 916cc, 80 shot, 6.20's at 111 mph. (Her RIDE) |
|
|
|
|
05-10-2010, 12:25 AM
|
#8 |
|
Ready to go fast!!
Join Date: Aug 2008
Location: Carthage,Mo
Posts: 219
|
Re: It's baaaaaaaack!
i watched it too! ol' man runnin the show lol
__________________
454 block .30 forged aluminum pistons steel crank valve job Holley Strip Dominator intake 1030cfm holley carb, 250 plate shot roller rockers Erson Solid cam split duration 307/310. .575/.595 lift milodon oil pan fab. aluminum valve covers 4 bolt main splayed anodized caps all studded |
|
|
|
|
05-10-2010, 09:49 AM
|
#9 |
|
Registered User
Join Date: Jun 2006
Location: Jackson, Mo.
Posts: 607
|
Re: It's baaaaaaaack!
Looks good Marv! Looks like the plugs should all be fairly easy to get to, also.
__________________
Chris 1966 Chevy C10 LWB, 434 sbc, TH350, 12-bolt, factory suspension, pump gas 7.02 @ 95.8, 1.45 60' 1965 Chevy C10 LWB, 355 sbc, TH350, daily driver |
|
|
|
|
05-10-2010, 10:56 AM
|
#10 |
|
Registered Truck Offender
Join Date: May 2008
Location: hells training ground (aka Ariz)
Posts: 3,118
|
Re: It's baaaaaaaack!
Thanks guys. I tell ya I'm just glad to be back working on it again.
Midevil,, Good eye man. I dyno'd this motor with the 2" to 2-1/8" stepped Lemons for my Nova. It made good power up in the 6800-7k range but were not going that high now, and putting it on a T-stop to keep it slowed down,,.... 1-7/8" and running through the mufflers to keep it street legal seemed like the right choice. Besides, Primaries are about 14" longer than the Lemons. Jody put the slip collector dead at the trans cross member  It's pretty much the Headman Hustler roadster header tucked up inside the chassis. Pretty frickin cool! Yesterday I ran to Tuscon and took my mom to lunch, back here and took my wife to dinner, and still had time to spend with the girlfriend,, assembeled her yoke to and painted her driveshaft  ...put the dash in place just to see if I like the new configuration or not. The original dash .... HA, only thing that worked was the turn indicators and brights indicator, So a couple of cheep LED's from Radioshack does that and moved all the gauges up to the dash.  Then scattered some of the junk around the cab floor and tried to decide what I needed to build, and where I wanted to mount all this crap.  Still a big list to throw at this thing,,, but at least it's moving forward again. Making progress is almost as much fun as going to the  bar. suuuure it is 
__________________
Still playin with trucks, even at my age! When you're dead, it's only a problem for the people around you, because you don't know you're dead. .....It's kinda the same when your STUPID. I just did my taxes and reviewed my SS statement. Thanks to the current administration it looks like I will only have to work till noon on the day of my funeral. Last edited by Marv D; 05-10-2010 at 10:57 AM. |
|
|
|
|
05-10-2010, 09:05 PM
|
#11 |
|
Registered User
Join Date: Oct 2006
Location: bridgecreek ok.
Posts: 1,214
|
Re: It's baaaaaaaack!
looks great... who's going to coat them?
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=494388 431 big block times, changed to a 6.0 ls with turbo 1.58- 60' 7.18- 1/8th mile@95.18 11.37- 1/4 @115.81 |
|
|
|
|
05-11-2010, 03:10 PM
|
#12 | |
|
Registered Truck Offender
Join Date: May 2008
Location: hells training ground (aka Ariz)
Posts: 3,118
|
Re: It's baaaaaaaack!
Quote:
I run just over 1300° exhaust temps on the top end of the track and they look as good as the day I coated them. A buddy reached in to pull the plug wires and burned his Mechanix gloves all over the #4 tube. 4 passes and it cooked the nylon out and it wiped off,,, looked like brand new again. They do nice work http://www.small-block-chevy.com/ima...0/novahdr1.JPG http://www.small-block-chevy.com/ima...0/novahdr2.JPG http://www.small-block-chevy.com/ima...0/novahdr3.JPG I built 2 tubes before taking this up to J-fab and I'll tell you what. ANYONE with the patients to fabricate / design and build headers, even with a weld-up kit, has my respect. I love TIG welding, I love fabrication, I love spending time making something from a pile of ????. But that header fabriaction is a monumental PITA!!!
__________________
Still playin with trucks, even at my age! When you're dead, it's only a problem for the people around you, because you don't know you're dead. .....It's kinda the same when your STUPID. I just did my taxes and reviewed my SS statement. Thanks to the current administration it looks like I will only have to work till noon on the day of my funeral. |
|
|
|
|
|
05-10-2010, 10:57 PM
|
#13 |
|
Registered User
Join Date: Nov 2007
Location: Bay Area, Ca
Posts: 2,841
|
Re: It's baaaaaaaack!
Looks great Marv..
I was thinking about fabing up a set of headers for my pile in the near future. I was thinking since I don't have inner fenders and won't when I finally put the glass front on, perhaps running them over the top of the frame then down, so 12" or so before the first bend. I've heard good things about doing things like that. But then I'm thinking, ok, is it worth the 10ish hp right now or should I do a mustang 2 front next?
__________________
------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49 |
|
|
|
|
05-11-2010, 12:07 AM
|
#14 |
|
My Carbon Footprint
Join Date: Oct 2008
Location: Orygun
Posts: 5,527
|
Re: It's baaaaaaaack!
That's so funny. The pics where you can see your one proform.....I didn't catch on at first that it was a tunnel ram. I was about to type a huge WTF????? lol
Looked weird but makes sense now and nice headers. Nothing like a little tig welding. |
|
|
|
|
05-11-2010, 06:18 AM
|
#15 |
|
Registered User
Join Date: Mar 2008
Location: tyler texas
Posts: 1,538
|
Re: It's baaaaaaaack!
Looks really good Marv...
__________________
NHRA Super Street 469C It only runs 10.90 at 156 mph |
|
|
|
|
05-11-2010, 08:04 AM
|
#16 |
|
Registered User
Join Date: Jan 2008
Location: St.Petersburg,Fl
Posts: 1,267
|
Re: It's baaaaaaaack!
Very nice work! I've built several sets myself, and it's really nice to see when a header builder works around the plugs, and makes things easier on the tuner.Keep up the good work! Awesome truck, by the way!
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
