Replacing the stock air filter/valve covers? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

muthstryker · 08-31-2010, 10:58 AM

Hey guys,

Was going to swap out my Airfilter/Valve Covers, Well, was wondering what lines I can remove, there is all these air lines ect going to the airfilter housing, the valve covers ect ect. Is there anything I dont need and anything I have to have?

Some Pics of The Motor

*nbpro* · 08-31-2010, 04:26 PM

I'm thinking this would all depend on your state emission laws.

BigRed76 · 08-31-2010, 05:54 PM

This is my personal opinion but if your whole stock setup is complete and works i wouldn't mess with it unless emissions isn't a concern.

muthstryker · 08-31-2010, 05:58 PM

My truck will be exempt in 2011 so im not worried about emissions, My valve covers leak really really bad right now to the point where I wont drive it. I just figured since im replacing alot of stuff I would just swap the valve covers out with some fabricated aluminum ones as well as a spun aluminum air cleaner..

*nbpro* · 08-31-2010, 06:19 PM

have a look here valve covers aluminum air cleaner and engine bays
http://67-72chevytrucks.com/vboard/s...d.php?t=364147

79gmcc15 · 08-31-2010, 07:34 PM

Make sure you don't have to take the sniff test next year. even if it is exempt next year, if you didn't get it done this year, you could still have to take the test.

BigRed76 · 08-31-2010, 09:08 PM

i agree with 79GMC15, but if your truck is gonna be exempt from emmisions then i'd take it all off lol sell it to someone in california who needs it

CaliDude76 · 08-31-2010, 09:52 PM

Quote:

Originally Posted by BigRed76

i agree with 79GMC15, but if your truck is gonna be exempt from emmisions then i'd take it all off lol sell it to someone in california who needs it

Ha.. and I'm sure they'll be plenty of takers.... post it up on E-Bay!
They're rediculous here about the smog reg's

It's really hard to find somebody who's even willing to tinker with these q-jets anymore... to get them to pass (or even knows how to)

Wild83C10 · 08-31-2010, 09:32 PM

Don't get any stamped cheap valve covers. Go with some nice cast aluminum ones from proform. They will seal much better then the stamped junk.

Also keep the PCV setup so that it will pull out some of the crankcase pressure.

The charcoal canister for the fuel tank is probably a good idea to keep as well so that you evec all the fuel fumes/vapors.

motornut · 08-31-2010, 09:41 PM

i use an old breather i had,with newer chrome covers.till i get the body done i'm just keepin the 85 Suburban goin.

BigRed76 · 08-31-2010, 09:50 PM

Quote:

Originally Posted by Wild83C10

Don't get any stamped cheap valve covers. Go with some nice cast aluminum ones from proform. They will seal much better then the stamped junk.

Also keep the PCV setup so that it will pull out some of the crankcase pressure.

The charcoal canister for the fuel tank is probably a good idea to keep as well so that you evec all the fuel fumes/vapors.

oh yeah didnt really consider the evap system, it is nice not to smell gas all the time.

Rpratt · 09-01-2010, 11:42 AM

I know you are going to do what you want to do, but that is a very clean stock setup, I wouldn't change anything but the gaskets.

motornut · 09-01-2010, 12:09 PM

on the pcv valve i had to cut one pvc for the metal shell to fit factory rubber grommet/then the one that came with the covers

08-31-2010, 10:58 AM	#1
muthstryker Registered User Join Date: Dec 2009 Location: Snohomish, Washington Posts: 1,187	Replacing the stock air filter/valve covers? Hey guys, Was going to swap out my Airfilter/Valve Covers, Well, was wondering what lines I can remove, there is all these air lines ect going to the airfilter housing, the valve covers ect ect. Is there anything I dont need and anything I have to have? Some Pics of The Motor

08-31-2010, 04:26 PM	#2
nbpro Account Suspended Join Date: Dec 2008 Location: Huntsville,AL Posts: 2,119	Re: Replacing the stock air filter/valve covers? I'm thinking this would all depend on your state emission laws.

08-31-2010, 05:54 PM	#3
BigRed76 Registered User Join Date: Jan 2010 Location: Loveland, CO Posts: 1,921	Re: Replacing the stock air filter/valve covers? This is my personal opinion but if your whole stock setup is complete and works i wouldn't mess with it unless emissions isn't a concern. __________________ Zach 1970 Chevrolet Custom Camper K20 1971 GMC Super K2500, 12V/NV4500 swap in progress 1971 Chevrolet Custom C10 1972 Chevrolet Custom Deluxe C20, 5.3/4L60E 1972 Oldsmobile Cutlass Supreme, 455/TH400, 3.73 posi 2004 GMC Sierra 2500HD, LB7/Allison, CCSB 2005 GMC Sierra 1500, 5.3/4L60E, CCSB

08-31-2010, 05:58 PM	#4
muthstryker Registered User Join Date: Dec 2009 Location: Snohomish, Washington Posts: 1,187	Re: Replacing the stock air filter/valve covers? My truck will be exempt in 2011 so im not worried about emissions, My valve covers leak really really bad right now to the point where I wont drive it. I just figured since im replacing alot of stuff I would just swap the valve covers out with some fabricated aluminum ones as well as a spun aluminum air cleaner..

08-31-2010, 06:19 PM	#5
nbpro Account Suspended Join Date: Dec 2008 Location: Huntsville,AL Posts: 2,119	Re: Replacing the stock air filter/valve covers? have a look here valve covers aluminum air cleaner and engine bays http://67-72chevytrucks.com/vboard/s...d.php?t=364147

08-31-2010, 07:34 PM	#6
79gmcc15 Gettin It One Pice At A Time Join Date: Oct 2004 Location: everett, washington Posts: 2,688	Re: Replacing the stock air filter/valve covers? Make sure you don't have to take the sniff test next year. even if it is exempt next year, if you didn't get it done this year, you could still have to take the test. __________________ RIP ELJAY Work In Progress 1979 GMC C1500 Trailering Special. Getting the truck done, one piece at a time. “You can tell a lot about a fellow’s character by his way of eating jellybeans.”Ronald Reagan “I don’t know the key to success but I know the key to failure is trying to please everybody.” Bill Cosby

08-31-2010, 09:08 PM	#7
BigRed76 Registered User Join Date: Jan 2010 Location: Loveland, CO Posts: 1,921	Re: Replacing the stock air filter/valve covers? i agree with 79GMC15, but if your truck is gonna be exempt from emmisions then i'd take it all off lol sell it to someone in california who needs it __________________ Zach 1970 Chevrolet Custom Camper K20 1971 GMC Super K2500, 12V/NV4500 swap in progress 1971 Chevrolet Custom C10 1972 Chevrolet Custom Deluxe C20, 5.3/4L60E 1972 Oldsmobile Cutlass Supreme, 455/TH400, 3.73 posi 2004 GMC Sierra 2500HD, LB7/Allison, CCSB 2005 GMC Sierra 1500, 5.3/4L60E, CCSB

08-31-2010, 09:32 PM	#9
Wild83C10 Registered User Join Date: May 2002 Location: NJ Posts: 910	Re: Replacing the stock air filter/valve covers? Don't get any stamped cheap valve covers. Go with some nice cast aluminum ones from proform. They will seal much better then the stamped junk. Also keep the PCV setup so that it will pull out some of the crankcase pressure. The charcoal canister for the fuel tank is probably a good idea to keep as well so that you evec all the fuel fumes/vapors. __________________ 83 C10 Stepside (SOLD, it was a blast!) 383 MASS-FLO EFI/TKO II 600/3.90 Posi 10 bolt S475 and C4 DM running, fine tuning turbo= Douchebag Racing: Runs Fine all the Time

08-31-2010, 09:41 PM	#10
motornut 78K & 79C Jimmys Join Date: Nov 2009 Location: Ottawa Ont CANADA Posts: 7,901	Re: Replacing the stock air filter/valve covers? i use an old breather i had,with newer chrome covers.till i get the body done i'm just keepin the 85 Suburban goin. Attached Images __________________ John 1978 GMCJimmy4X4-350/203 1979 GMCJimmy4X2-305/350 Last edited by motornut; 08-31-2010 at 09:43 PM.

09-01-2010, 11:42 AM	#12
Rpratt Registered User Join Date: Mar 2010 Location: Grand Rapids Mi Posts: 47	Re: Replacing the stock air filter/valve covers? I know you are going to do what you want to do, but that is a very clean stock setup, I wouldn't change anything but the gaskets.

09-01-2010, 12:09 PM	#13
motornut 78K & 79C Jimmys Join Date: Nov 2009 Location: Ottawa Ont CANADA Posts: 7,901	Re: Replacing the stock air filter/valve covers? on the pcv valve i had to cut one pvc for the metal shell to fit factory rubber grommet/then the one that came with the covers __________________ John 1978 GMCJimmy4X4-350/203 1979 GMCJimmy4X2-305/350

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.