looking to buy a intake for 66 250 6 cylinder - The 1947 - Present Chevrolet & GMC Truck Message Board Network

truckman32 · 03-02-2003, 05:13 PM

i need a 66 model intake for a 250 straight 6 engine,i need a driverside door for a 62 chevy c10 any hot rod parts for the 6 banger i'll buy them

chevy lover · 03-02-2003, 05:59 PM

try to find an offenhouser or clifford intake for good performance

truckman32 · 03-02-2003, 09:21 PM

thanks ,do you know were i can order performance parts for the 250

chevy lover · 03-03-2003, 01:21 AM

http://www.cliffordperformance.com/

try this site. might be a little pricy but good stuff.
My friend and I built his 250 that was in a 69 nova. bored out, head was milled and had a crane cam with a offenhuaser 4 barrel intake with holley 600. that motor had enough horse and torgue to bust the trans so he ended up having one built. And if I had to take a guess at the hp I would put it at around 350-400hp.

truckman32 · 03-04-2003, 12:43 AM

i checked out the site no intakes for chevy 250

chevy lover · 03-04-2003, 09:13 AM

ok, sorry i didn't look that close to the site. I know the intake on the 250 we built was an offenhauser. with that the only thing i can tell you is check you local speed shops or try JEGS or Summit.

03-02-2003, 05:13 PM	#1
truckman32 AND HOLDING ON TO THE C10 Join Date: Jan 2003 Location: MT.STERLING,KY Posts: 390	looking to buy a intake for 66 250 6 cylinder i need a 66 model intake for a 250 straight 6 engine,i need a driverside door for a 62 chevy c10 any hot rod parts for the 6 banger i'll buy them

03-02-2003, 05:59 PM	#2
chevy lover HMMMM Chevy Join Date: Aug 2002 Location: Quakertown, Pa Posts: 203	try to find an offenhouser or clifford intake for good performance __________________ 68 Chevy C10 swb(under construction) 82 GMC K1500 6.2l diesel (daily driver) 77 Chevy K30 frame (only thing left is axles and trans/transfer)______________________________ Mike

03-02-2003, 09:21 PM	#3
truckman32 AND HOLDING ON TO THE C10 Join Date: Jan 2003 Location: MT.STERLING,KY Posts: 390	thanks ,do you know were i can order performance parts for the 250 __________________ 66 swb/ss chevy c10 SOLD 62 swb/fs chevy c10 :p SOLD 84 swb/fs chevy c10 91 sdime 383/th350

03-03-2003, 01:21 AM	#4
chevy lover HMMMM Chevy Join Date: Aug 2002 Location: Quakertown, Pa Posts: 203	http://www.cliffordperformance.com/ try this site. might be a little pricy but good stuff. My friend and I built his 250 that was in a 69 nova. bored out, head was milled and had a crane cam with a offenhuaser 4 barrel intake with holley 600. that motor had enough horse and torgue to bust the trans so he ended up having one built. And if I had to take a guess at the hp I would put it at around 350-400hp. __________________ 68 Chevy C10 swb(under construction) 82 GMC K1500 6.2l diesel (daily driver) 77 Chevy K30 frame (only thing left is axles and trans/transfer)______________________________ Mike Last edited by chevy lover; 03-03-2003 at 01:28 AM.

03-04-2003, 12:43 AM	#5
truckman32 AND HOLDING ON TO THE C10 Join Date: Jan 2003 Location: MT.STERLING,KY Posts: 390	i checked out the site no intakes for chevy 250 __________________ 66 swb/ss chevy c10 SOLD 62 swb/fs chevy c10 :p SOLD 84 swb/fs chevy c10 91 sdime 383/th350

03-04-2003, 09:13 AM	#6
chevy lover HMMMM Chevy Join Date: Aug 2002 Location: Quakertown, Pa Posts: 203	ok, sorry i didn't look that close to the site. I know the intake on the 250 we built was an offenhauser. with that the only thing i can tell you is check you local speed shops or try JEGS or Summit. __________________ 68 Chevy C10 swb(under construction) 82 GMC K1500 6.2l diesel (daily driver) 77 Chevy K30 frame (only thing left is axles and trans/transfer)______________________________ Mike

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.