Spring Perch ?????? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

McMurray76 · 07-25-2011, 02:16 PM

I am the proud owner of a rusted out 77 K20 driver and a solid 86 C20 parts donor. Does anyone out there know if I can replace the rusty spring perches from the 77 K20 with the good ones from the 86 C20?

ghettoluxury · 07-25-2011, 09:38 PM

the perches on the axle have to be cut off the ones on the frame are rivited on and are a little lowerthan the 4x4 so you would get a little lift out of it.

If you are talking about the ones on the axle than you could just swap the axle out if the gears are the same ratio.

McMurray76 · 07-26-2011, 11:27 AM

I'm concerned about the forward ones on the frame. Could I use a piece of plate steel welded to the frame then re-attach the perch to the plate to off-set the difference in height? Thanks.

McMurray76 · 07-27-2011, 04:03 PM

Is there anyplace I can get re-pops?

trout · 07-27-2011, 05:48 PM

are you talking bout the hangers on the frame? or were the rearend bolts the the leaf that little plat???

McMurray76 · 07-28-2011, 11:39 AM

The forward hanger on the frame.

trout · 07-28-2011, 02:10 PM

yea they should be the same

McMurray76 · 08-04-2011, 02:03 PM

Thanks!

07-25-2011, 02:16 PM	#1
McMurray76 Registered User Join Date: Dec 2009 Location: Columbus ohio Posts: 109	Spring Perch ?????? I am the proud owner of a rusted out 77 K20 driver and a solid 86 C20 parts donor. Does anyone out there know if I can replace the rusty spring perches from the 77 K20 with the good ones from the 86 C20?

07-25-2011, 09:38 PM	#2
ghettoluxury Registered User Join Date: Apr 2009 Location: Waynesfield Ohio Posts: 1,991	Re: Spring Perch ?????? the perches on the axle have to be cut off the ones on the frame are rivited on and are a little lowerthan the 4x4 so you would get a little lift out of it. If you are talking about the ones on the axle than you could just swap the axle out if the gears are the same ratio. __________________ 1949 Five Window, 1973 Step Side, 2000 Z71

07-26-2011, 11:27 AM	#3
McMurray76 Registered User Join Date: Dec 2009 Location: Columbus ohio Posts: 109	Re: Spring Perch ?????? I'm concerned about the forward ones on the frame. Could I use a piece of plate steel welded to the frame then re-attach the perch to the plate to off-set the difference in height? Thanks.

07-27-2011, 04:03 PM	#4
McMurray76 Registered User Join Date: Dec 2009 Location: Columbus ohio Posts: 109	Re: Spring Perch ?????? Is there anyplace I can get re-pops?

07-27-2011, 05:48 PM	#5
trout Registered User Join Date: Jun 2010 Location: lexington, SC Posts: 1,276	Re: Spring Perch ?????? are you talking bout the hangers on the frame? or were the rearend bolts the the leaf that little plat??? __________________ Edited by staff

07-28-2011, 11:39 AM	#6
McMurray76 Registered User Join Date: Dec 2009 Location: Columbus ohio Posts: 109	Re: Spring Perch ?????? The forward hanger on the frame.

07-28-2011, 02:10 PM	#7
trout Registered User Join Date: Jun 2010 Location: lexington, SC Posts: 1,276	Re: Spring Perch ?????? yea they should be the same __________________ Edited by staff

08-04-2011, 02:03 PM	#8
McMurray76 Registered User Join Date: Dec 2009 Location: Columbus ohio Posts: 109	Re: Spring Perch ?????? Thanks!

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.