Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
|
09-17-2011, 02:14 AM | #1 |
Registered User
Join Date: Sep 2011
Location: douglas,wy
Posts: 14
|
big block swap with a 4 spd
I am trying to figure out how to put headers on my 72 blazer with the original 4 spd in it. I cant find the right header's or figure out how to rearrange clutch linkage around to make it work. the z bar is in the way. any suggestions
|
09-17-2011, 10:55 AM | #2 |
Registered User
Join Date: Sep 2011
Location: san diego, ca.
Posts: 51
|
Re: big block swap with a 4 spd
I am kinda in the same predicament, first what did you do about clearance with the firewall ? body lift ? move engine forward ?
I have the tall valve covers on due to the roller rockers. I am running hedman shorty headers and the clutch linkage is not gonna work with them so I went online and found a hydraulic clutch setup for my truck but.... of course there is a but ....some fabrication is going to be needed, I need to make a bracket to bolt to the bellhousing to hold the slave cylinder and then need to fabricate the rod to attach to the clutch pedal and then to the master cylinder that will be on the firewall....fun stuff huh but it is either that or change everything to an auto-tranny and spend that much more money.... also are you using a long or short water pump ? and which side is your alternator mounted on ? if you could could you email me at ncjthree@gmail.com thanks Nick |
09-18-2011, 04:10 PM | #3 |
Senior Member
Join Date: Feb 2001
Location: New Madison, Ohio
Posts: 21,375
|
Re: big block swap with a 4 spd
bump
__________________
A husband can be right...or...A husband can be happy. 67-72 Chevy and GMC Trucks...The Classic Truck for the Classic Folk. 1970 CST Two tone green, 402BB, 400 Automatic, Tach, Buckets, AC, AM-FM, Tilt, GM CB, GM 8 Tract, LWB, etc JOHN 17:3...The better side of "LIFE" Remember: Everyday is a good day...Some are just gooder! |
09-18-2011, 11:17 PM | #4 |
Registered User
Join Date: Sep 2011
Location: douglas,wy
Posts: 14
|
Re: big block swap with a 4 spd
|
09-19-2011, 09:54 AM | #5 |
Registered User
Join Date: Feb 2000
Location: Modesto, CA
Posts: 1,842
|
Re: big block swap with a 4 spd
Bump just means he is "bumping" your thread to the top of the list of threads..most likely he is looking for the same answers as you are.
I have a 454 in my K5. I installed it in the stock location and I converted my manual linkage to Hydro when I did the swap. With my 350 I had manual linkage and ran Hedmen Elite series headers, I had to move the Z-bar just about 1" on the frame side of the Z-bar. On top of my frame was the Z-bar mount bracket. I drilled a hole in the bracket and re-mounted the Zbar end about 1" towards the firewall and that alowed the heades to fit and the Z-bar still worked..thoes ball mount ends pivot well. Anyway don't know it this helps with a BBC..?
__________________
1972 K5 MPFI454/Sm465/Np205/D60/14FFd/Re-Centerd H1s w/Swamper Iroks |
09-23-2011, 07:44 AM | #6 | |
Registered User
Join Date: Sep 2011
Location: douglas,wy
Posts: 14
|
Re: big block swap with a 4 spd
Quote:
|
|
09-18-2011, 11:15 PM | #7 |
Registered User
Join Date: Sep 2011
Location: douglas,wy
Posts: 14
|
Re: big block swap with a 4 spd
Im abble to leave the engine right there. im using short valve covers. I did have to push the fire wall back a little to clear the dist cap. my alt is on the passenger side.
|
Bookmarks |
Thread Tools | |
Display Modes | |
|
|