NC Looking for cheap, broken, cracked, chipped a/c vent ball housings - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**NC67Chev** · 07-08-2012, 09:05 PM

This might sound a little weird, but I'm looking for a rt & lt vent ball housing to use as a template. I want a set that's basically not good enough to use. Thanks!

VA72C10 · 07-09-2012, 02:18 AM

ttt for you. I might have a broken useable set for a template but likely will be a while before I can get to the box to look for them so hopefully someone else has a set....or has a template for you...I remember seeing one on the board in the FAQ section likely?

**NC67Chev** · 07-09-2012, 10:51 AM

Thanks! I have templates, but I want the most assurance possible before I do any cutting. I'm essentially going to cut the connector off of the back of the housing so it will sit flush against the dash.

jwodahl · 07-09-2012, 11:07 AM

if the template ends up being correct after all is said and done, please let me know where you got it..

07-08-2012, 09:05 PM	#1
NC67Chev Senior Member Join Date: Oct 2009 Location: Greensboro, NC Posts: 699	Looking for cheap, broken, cracked, chipped a/c vent ball housings This might sound a little weird, but I'm looking for a rt & lt vent ball housing to use as a template. I want a set that's basically not good enough to use. Thanks! __________________ 1967 Chevy C-10, 250 L6, Powerglide, 3.73, SWB, Fleetside Upgrades: Power steering, Offset air cleaner, Rear Sport bumper, 3 point safety belts, HEI, -1/-2 springs, 16x5 wheels, McGaughy's disc brake conversion, Sway bar

07-09-2012, 02:18 AM	#2
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,267	Re: Looking for cheap, broken, cracked, chipped a/c vent ball housings ttt for you. I might have a broken useable set for a template but likely will be a while before I can get to the box to look for them so hopefully someone else has a set....or has a template for you...I remember seeing one on the board in the FAQ section likely? __________________ Looking for a 67-72 swb or blazer project in or around VA.

07-09-2012, 10:51 AM	#3
NC67Chev Senior Member Join Date: Oct 2009 Location: Greensboro, NC Posts: 699	Re: Looking for cheap, broken, cracked, chipped a/c vent ball housings Thanks! I have templates, but I want the most assurance possible before I do any cutting. I'm essentially going to cut the connector off of the back of the housing so it will sit flush against the dash. __________________ 1967 Chevy C-10, 250 L6, Powerglide, 3.73, SWB, Fleetside Upgrades: Power steering, Offset air cleaner, Rear Sport bumper, 3 point safety belts, HEI, -1/-2 springs, 16x5 wheels, McGaughy's disc brake conversion, Sway bar

07-09-2012, 11:07 AM	#4
jwodahl Registered User Join Date: Jun 2012 Location: crosby, tx Posts: 114	Re: Looking for cheap, broken, cracked, chipped a/c vent ball housings if the template ends up being correct after all is said and done, please let me know where you got it..

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.