![]() |
|
![]() |
#1 |
Registered User
Join Date: May 2012
Location: colorado
Posts: 114
|
aftermarket heaters
has anyone used any aftermarket heaters besides vintage air? found some that are pretty reasonable in price and I only want a heater without a/c. the ones I have looked at are really small and seem like they would do just fine in a small cab hooked up to defrost. if possible some pictures thanks
|
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Jun 2006
Location: Idaho
Posts: 8,800
|
Re: aftermarket heaters
Stock Chevy truck and auto heating cores are only about 4x8x2 inches with a pretty small fan. Most add-on heaters were just a box with the core, fan and flaps to direct air. I would look for one that was more rectangular horizontally so it tucks up under the dash a little. I remember my grandmother getting on me as a kid for kicking the box that hung under the dash in her Willys Wagon. Googling "truck cab heater" turns up a bunch. Ideally you would want one with round hose connections for the defront vents and your choice of flappers for floor or front discharge.
__________________
1959 Chevy Short Fleetside w/ 74 4WD drive train (current project) OrrieG Build Thread 1964 Chevelle Malibu w/ 355-350TH (daily driver) Helpful AD and TF Manual Site Old Car Manual Project |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Aug 2012
Location: Salem Mo
Posts: 670
|
Re: aftermarket heaters
I installed one from classic parts. You get the complete heater along with duct hose and the connectors to mount up to the defrost outlets under the dash. Like everything else I had to do some tweeking to get the fit I wanted but it should do the job well.
I mentioned before, the heater hoses will not work with the battery in the stock location, they are too high. I also wanted mine as far up into the dash as I could, I shortened the glove box to do this. Pics. |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Dec 2011
Location: visalia ca
Posts: 1,480
|
Re: aftermarket heaters
I was looking at one of those but I don't want to lose my glove box that much. anyone running anything else? winters coming and aint about to drive with foggy windows. I have my stock standard heater but I know it aint cheap to fix the leaky core
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: May 2012
Location: colorado
Posts: 114
|
Re: aftermarket heaters
I have made the decision to mount mine behind the seat and run ducts to the defrost vents and use the other two vents for the cab. I bought mine off e bay for cheap, and it is a little bigger than i wanted but after seeing a episode of *****en Rides, they mounted a/c and heater in the rear of a 4 door Plymouth and it worked and looked awesome. Besides I have my fuse block in my glove box. Hope this helps.
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Jun 2006
Location: Idaho
Posts: 8,800
|
Re: aftermarket heaters
Did you route the defrost vents through a center console or?? I would think that if they go any distance the heat would discipate and all you would get is cold air?
__________________
1959 Chevy Short Fleetside w/ 74 4WD drive train (current project) OrrieG Build Thread 1964 Chevelle Malibu w/ 355-350TH (daily driver) Helpful AD and TF Manual Site Old Car Manual Project |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Dec 2011
Location: visalia ca
Posts: 1,480
|
Re: aftermarket heaters
What are you running orrieG?
|
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Aug 2013
Location: Chino Valley, Az
Posts: 41
|
Re: aftermarket heaters
Same Classic trk Parts heater as Stepside Jim used. This is in my 48GMC. Put mine in the middle as you can see. I have bucket seats so it is not in the way of any passengers, especially any "little OrrieG's". Plus I want my share of the heat!!. I would think that both windshields will get equal defroggin also.
![]()
__________________
![]() |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|