Canada Porterbuilt extreme rear

[exploderjim]

Selling Porterbuilt rear extreme set up, tubular transmission cross member, rear frame cross member.

Weld in notch welded in Blazer frame in picture. I will remove it and remove bridge assembly for shipping. sand blasted for painting but decided to stop the build. Trailing arm Cross member to be removed from frame as well.

Asking: $ 1,300 plus shipping

That's $800 less than PB plus shipping and no wait.

The Dropmember Rear Trailing Arm Kit includes the following:
-Weld-in notch assemblies with notch caps
-Bolt-in bridge assembly - outboard bag location
-Firestone F9000 air springs
-KYB shocks
-Weld on lower bag mounts
-Fully adjustable trac-bar
-Tubular adjustable trailing arm x-member - 2 piece drive shaft
-Tubular 1″ drop trailing arms with 2" blocks
-Lower shock bar assembly
-All mounting hardware

[leddzepp]

I am interested in the trailing arm cross member since it is for a two piece driveshaft, if you split this stuff up. Thanks.

[budnikguy]

Scott I have a couple of PB trailing arm crossmembers..can check if they are 2 piece drive shaft style..

Adam

Originally Posted by leddzepp

I am interested in the trailing arm cross member since it is for a two piece driveshaft, if you split this stuff up. Thanks.

[82swb]

Please note that you must be a supporting member to post classified items. This includes but is not limited to What Its Worth, Want To Buy, Want To Trade, and For Sale. Please consider supporting the forum by subscribing. Further information on the subscription levels available are located here

If you need any further assistance with that please contact any Admin for help.

[82swb]

Originally Posted by 82swb

Please note that you must be a supporting member to post classified items. This includes but is not limited to What Its Worth, Want To Buy, Want To Trade, and For Sale. Please consider supporting the forum by subscribing. Further information on the subscription levels available are located here

If you need any further assistance with that please contact any Admin for help.

Sorry, I was just inquiring about a part mentioned earlier in the thread. I didn't think you had to support the board to buy product from board members.

[leddzepp]

Originally Posted by 82swb

Sorry, I was just inquiring about a part mentioned earlier in the thread. I didn't think you had to support the board to buy product from board members.

You don't when you are buying a part from the OP of the thread. It's considered hijacking otherwise. If there is a part you are looking for or in need of, you need to post a want to buy ad by starting your own thread. In order to post a want to buy ad you must be a subscribing member.

[budnikguy]

duplicate post

[budnikguy]

Very Interested! Little concerned with shipping cost....Freight or Greyhound possible? I have a business address at 92557, residence at 92508, and or have a Greyhound station in Riverside, CA.
Please lmk...

[exploderjim]

Forgive me but How do I even get a shipping estimate from greyhound?

[budnikguy]

You can get a quote on their web site....they take up to 100 pounds per package, and you enter, to and from, locations. Would be easy to wrap them in cardboard and or padding..and just tape it up. Would not necessarily have to box things

Originally Posted by exploderjim

Forgive me but How do I even get a shipping estimate from greyhound?

[exploderjim]

Pm me what you think would be fair.

[exploderjim]

If I estimate 3 packages at 100lbs each package is $100. I can't see these weighing that much. so I would say under $250 via greyhound. Anymore than that I would cover.

[budnikguy]

pm sent

[exploderjim]

Sold pending payment

[Hardesty454]

if sale falls through Id be interested in a few of the items or all if possible. Thanks!

[exploderjim]

Sold