AN Fitting Questions - The 1947 - Present Chevrolet & GMC Truck Message Board Network

78SilveradoSWB · 08-10-2003, 02:29 PM

I see some people using AN fittings and braided hoses in the engine compartment. In looking at Summt & Jeg catalogs they look nice and expensive. How do they work? Do you need clamps to secure the hoses into the fittings or is there some sort of retainer built inside.

87 STEPPER · 08-10-2003, 04:20 PM

Well.........The best one's are sweged on but not to many people have the hydraulic crimp tool to do that so every one uses the self ancoring one's.

The fitting has a collar that slip's over the hose and the other half of the fitting is insetred into the hose and collar and threaded togeather thus applying a compression type ancoring system that's good for up too 3000psi if accomplished correctly.

**swervin ervin** · 08-10-2003, 04:49 PM

My tranny cooler hoses and fuel hose is full AN fittings. No special tool needed to put them together. You are right, they are expensive, as is the stainless hose.

Best I can describe the way they work is like a normal air hose.

Here is a assembly sheet from my Aeroquip catalog.

Cole's 87 · 08-10-2003, 04:53 PM

Dang Mike you type too fast

.......

There is some more good info on the AN fittings

http://www.russellperformance.com/au...l_flow_how.htm

78SilveradoSWB · 08-10-2003, 05:19 PM

Thanks Guys!

They sure look alot better and professional looking than a black hose to a barb connector and a hose clamp!

08-10-2003, 02:29 PM	#1
78SilveradoSWB Senior Member Join Date: Apr 2002 Location: Beaverton, OR Posts: 1,615	AN Fitting Questions I see some people using AN fittings and braided hoses in the engine compartment. In looking at Summt & Jeg catalogs they look nice and expensive. How do they work? Do you need clamps to secure the hoses into the fittings or is there some sort of retainer built inside. __________________ Mitch 1978 Chevrolet Silverado C 10 454 BB, TH400

08-10-2003, 04:20 PM	#2
87 STEPPER STILL PLAYS WITH TRUX Join Date: Nov 2002 Location: Melbourne, Fla. Posts: 2,764	Well.........The best one's are sweged on but not to many people have the hydraulic crimp tool to do that so every one uses the self ancoring one's. The fitting has a collar that slip's over the hose and the other half of the fitting is insetred into the hose and collar and threaded togeather thus applying a compression type ancoring system that's good for up too 3000psi if accomplished correctly. __________________ ~~Bruce~~ MY 87 STEPPER MY 99 2D/WD TAHOE

08-10-2003, 04:49 PM	#3
swervin ervin You get what you pay for Join Date: Dec 1999 Location: Cherryville, NC Posts: 4,798	My tranny cooler hoses and fuel hose is full AN fittings. No special tool needed to put them together. You are right, they are expensive, as is the stainless hose. Best I can describe the way they work is like a normal air hose. Here is a assembly sheet from my Aeroquip catalog. __________________ Mike 1985 Chevy C-10

08-10-2003, 05:19 PM	#5
78SilveradoSWB Senior Member Join Date: Apr 2002 Location: Beaverton, OR Posts: 1,615	Thanks Guys! They sure look alot better and professional looking than a black hose to a barb connector and a hose clamp! __________________ Mitch 1978 Chevrolet Silverado C 10 454 BB, TH400

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

08-10-2003, 04:53 PM	#4
Cole's 87 Registered User Join Date: Nov 2002 Posts: 272	Dang Mike you type too fast ....... There is some more good info on the AN fittings http://www.russellperformance.com/au...l_flow_how.htm



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.