Door panel mounting problems. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

ConradBSomething · 04-02-2015, 07:46 PM

So I'll start by saying that I used the search function with every combination of words that I could think of with squat for results. Just in case this is a really obvious issue that been talked about a couple dozen times already.

I'm getting ready to rebuild the innards of the door (felts, rubbers, etc) I noticed a few screws missing from the door panels, but now that I've got the panel off I see that the PO managed to strip the heads off of four of the screws and totally knock the square nut out of one hole.

Anybody ever deal with this?

jonzcustomshop · 04-02-2015, 08:05 PM

yes, on one truck I just didn't install the screw, but its a work truck!

on the other I welded a nut in the hole.

the 4 that are stripped , you may have to drill them out. on one truck I was able to weld a nut to the stripped part of the screw, and then unscrew it that way.

Modges'66 · 04-02-2015, 08:36 PM

I had a similar problem.
I didn't have the attachment screws so I bought a new set from Totally Stainless!
One of the nuts were missing though, so I glued it back on using an automotive epoxy for fixing bumpers, and when it started to get hard enough to stay in place, I screwed the door panel onto the door to improve position of the nut until the epoxy cured.
I have had the door panels off several times since without incident!
My doors & door-panels were painted at this point, soI did't want to weld.

Lugnutz65 · 04-02-2015, 10:42 PM

Quote:

Originally Posted by Modges'66

I had a similar problem.
. . . . . . so I glued it back on using an automotive epoxy for fixing bumpers, and when it started to get hard enough to stay in place, I screwed the door panel onto the door to improve position of the nut until the epoxy cured.
I have had the door panels off several times since without incident!
My doors & door-panels were painted at this point, soI did't want to weld.

The above seems like a very satisfactory solution. Modern epoxy should hold it in place just fine. I had the skin off my PS door so I just welded a new one into place.

jdl71 · 04-02-2015, 09:16 PM

I've also used JB weld to reattach the nut.

racecougar · 04-03-2015, 12:16 PM

Yep, I had to weld a couple nuts back into place on my driverside door. It isn't uncommon.

04-02-2015, 07:46 PM	#1
ConradBSomething Registered User Join Date: Sep 2012 Location: ringgold ga Posts: 91	Door panel mounting problems. So I'll start by saying that I used the search function with every combination of words that I could think of with squat for results. Just in case this is a really obvious issue that been talked about a couple dozen times already. I'm getting ready to rebuild the innards of the door (felts, rubbers, etc) I noticed a few screws missing from the door panels, but now that I've got the panel off I see that the PO managed to strip the heads off of four of the screws and totally knock the square nut out of one hole. Anybody ever deal with this?

04-02-2015, 08:05 PM	#2
jonzcustomshop 1961 crewcab Join Date: Dec 2007 Location: missoula, mt Posts: 6,164	Re: Door panel mounting problems. yes, on one truck I just didn't install the screw, but its a work truck! on the other I welded a nut in the hole. the 4 that are stripped , you may have to drill them out. on one truck I was able to weld a nut to the stripped part of the screw, and then unscrew it that way. __________________ 60 build: http://67-72chevytrucks.com/vboard/s...d.php?t=280904 61 crew build: http://67-72chevytrucks.com/vboard/s...d.php?t=646830 63 build: http://67-72chevytrucks.com/vboard/s...d.php?t=336537 64 'burb build: http://67-72chevytrucks.com/vboard/s...d.php?t=448681 65 'burb build: http://67-72chevytrucks.com/vboard/s...d.php?t=590715 65 build: http://67-72chevytrucks.com/vboard/s...d.php?t=281955

04-02-2015, 08:36 PM	#3
Modges'66 Registered User Join Date: Feb 2012 Location: Grand Rapids, Michigan, otherwise known as Beer City U.S.A. Posts: 1,081	Re: Door panel mounting problems. I had a similar problem. I didn't have the attachment screws so I bought a new set from Totally Stainless! One of the nuts were missing though, so I glued it back on using an automotive epoxy for fixing bumpers, and when it started to get hard enough to stay in place, I screwed the door panel onto the door to improve position of the nut until the epoxy cured. I have had the door panels off several times since without incident! My doors & door-panels were painted at this point, soI did't want to weld. __________________ My Build: http://67-72chevytrucks.com/vboard/s...d.php?t=512904

04-02-2015, 09:16 PM	#5
jdl71 Registered User Join Date: Oct 2012 Location: Eldon, MO Posts: 1,753	Re: Door panel mounting problems. I've also used JB weld to reattach the nut. __________________ Psalm 23 64 C10 66 K20

04-03-2015, 12:16 PM	#6
racecougar Registered User Join Date: Jan 2013 Location: Imperial, MO Posts: 1,003	Re: Door panel mounting problems. Yep, I had to weld a couple nuts back into place on my driverside door. It isn't uncommon. __________________ Rod @ AzzKicker Cars 1965 C10 SWB - Build Thread

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.