Sources for "basic" heater? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

BigSix · 04-11-2015, 09:54 PM

Is there a place that stocks the basic heater for our trucks? Not sure where to get one but the deluxe heater I have takes up too much underhood space. Any suggestions or places that stock this would be wonderful.

markeb01 · 04-12-2015, 01:08 AM

Junk yards or Ebay. That's where I found mine. I'm not aware of any supplier stocking originals.

BigSix · 07-25-2015, 08:34 PM

Do you know if I can use any 60-66 heater?

**Captainfab** · 07-26-2015, 01:05 AM

To my knowledge the recirculating heater was only used '60-'63. However, there is no reason one couldn't be installed into a '64-'66. You will use only 2 of the 3 levers on your heater control. The fan lever and the heat/defrost lever.

Quote:

Originally Posted by BigSix

Do you know if I can use any 60-66 heater?

**62 Longbed** · 07-26-2015, 02:47 AM

I believe I have one .. Will get pictures tomorrow ... PM'd you ..

edub981 · 07-26-2015, 09:57 AM

I got a basic heater from Ecklers. They were having a sale and I grabbed it for 9.95 plus shipping. I had a deluxe heater that was leaking and didn't want to spend the money to have it rebuilt (est. $350 @ the local shop) I had to mid if the housing as the inlet and outlets were for a basic not a deluxe. A little dremeling and she fits like a charm. Of course the heater is on all the time when I open the valve in the engine from the engine but for now I'm fine with the fix.
Posted via Mobile Device

LVPhotos · 07-26-2015, 10:25 AM

If you don't care about originality here are 2 from Speedway Motors.

http://www.speedwaymotors.com/Speedw...BTU,73715.html

http://www.speedwaymotors.com/Flex-A...eater,304.html

BigSix · 07-26-2015, 12:40 PM

With the economy heater in a 64-66 I can just adapt the cables to my stock controls? And just run a fan switch? In terms of shutting off hot water to the core I could always add a mechanical valve or does it have that from the factory?

RKS0069 · 07-26-2015, 02:22 PM

Just picked one up from http://www.aspenautoaz.com/ it came packaged well and was in great shape. I was able to get the dash lovers control cable switch and wires as well

BigSix · 07-26-2015, 02:24 PM

Thanks. I got the under hood part out today. Can I safely remove all the sheet metal ducting under the dash too if I intend on going with the economy setup?
Posted via Mobile Device

RKS0069 · 07-26-2015, 02:33 PM

Yes. The econo box replaces everything inside. If your soft duct lines are hard and cracked you might want to replace them as well.

BigSix · 07-26-2015, 05:36 PM

Thanks! The soft lines are completely missing. Removing that heater box from outside really opened up room for the twin turbos!

Mathew21 · 07-26-2015, 06:48 PM

Quote:

Originally Posted by BigSix

Thanks! The soft lines are completely missing. Removing that heater box from outside really opened up room for the twin turbos!

Twin turbo's awesome!

BigSix · 07-26-2015, 08:13 PM

It will only be awesome if I can get the plumbing to fit. Picture a bundle of snakes in a really small space. Thats about what its looking like.

04-11-2015, 09:54 PM	#1
BigSix Registered User Join Date: Mar 2014 Location: MD/VA/PA Or Inbetween Posts: 413	Sources for "basic" heater? Is there a place that stocks the basic heater for our trucks? Not sure where to get one but the deluxe heater I have takes up too much underhood space. Any suggestions or places that stock this would be wonderful.

04-12-2015, 01:08 AM	#2
markeb01 Senior Enthusiast Join Date: Feb 2007 Location: Spokane Valley, WA Posts: 8,356	Re: Sources for "basic" heater? Junk yards or Ebay. That's where I found mine. I'm not aware of any supplier stocking originals. __________________ My Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=444502

07-25-2015, 08:34 PM	#3
BigSix Registered User Join Date: Mar 2014 Location: MD/VA/PA Or Inbetween Posts: 413	Re: Sources for "basic" heater? Do you know if I can use any 60-66 heater?

07-26-2015, 02:47 AM	#5
62 Longbed Senior Member Join Date: Nov 2008 Location: Gresham , Oregon Posts: 588	Re: Sources for "basic" heater? I believe I have one .. Will get pictures tomorrow ... PM'd you ..

07-26-2015, 10:25 AM	#7
LVPhotos Registered User Join Date: Jan 2013 Location: Las Vegas, NV Posts: 1,857	Re: Sources for "basic" heater? If you don't care about originality here are 2 from Speedway Motors. http://www.speedwaymotors.com/Speedw...BTU,73715.html http://www.speedwaymotors.com/Flex-A...eater,304.html __________________ 1962 shortbed 408cui small block, TKO 600 5-speed, bagged Porterbuilt suspension. 18" Salt Flats http://www.cardomain.com/ride/332579...t-c-k-pick-up/ http://67-72chevytrucks.com/vboard/s...d.php?t=560081

07-26-2015, 09:57 AM	#6
edub981 Registered User Join Date: Mar 2013 Location: Fort Collins, CO Posts: 19	I got a basic heater from Ecklers. They were having a sale and I grabbed it for 9.95 plus shipping. I had a deluxe heater that was leaking and didn't want to spend the money to have it rebuilt (est. $350 @ the local shop) I had to mid if the housing as the inlet and outlets were for a basic not a deluxe. A little dremeling and she fits like a charm. Of course the heater is on all the time when I open the valve in the engine from the engine but for now I'm fine with the fix. Posted via Mobile Device

07-26-2015, 12:40 PM	#8
BigSix Registered User Join Date: Mar 2014 Location: MD/VA/PA Or Inbetween Posts: 413	Re: Sources for "basic" heater? With the economy heater in a 64-66 I can just adapt the cables to my stock controls? And just run a fan switch? In terms of shutting off hot water to the core I could always add a mechanical valve or does it have that from the factory?

07-26-2015, 02:22 PM	#9
RKS0069 Registered User Join Date: Jul 2015 Location: Milwaukie, Oregon Posts: 115	Re: Sources for "basic" heater? Just picked one up from http://www.aspenautoaz.com/ it came packaged well and was in great shape. I was able to get the dash lovers control cable switch and wires as well Attached Images __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=675881 1972 C-10 SWB 1962 3/4 ton LWB 2011 GMC Sierra LML Z71 crewcab shortbed

07-26-2015, 02:24 PM	#10
BigSix Registered User Join Date: Mar 2014 Location: MD/VA/PA Or Inbetween Posts: 413	Re: Sources for "basic" heater? Thanks. I got the under hood part out today. Can I safely remove all the sheet metal ducting under the dash too if I intend on going with the economy setup? Posted via Mobile Device

07-26-2015, 02:33 PM	#11
RKS0069 Registered User Join Date: Jul 2015 Location: Milwaukie, Oregon Posts: 115	Re: Sources for "basic" heater? Yes. The econo box replaces everything inside. If your soft duct lines are hard and cracked you might want to replace them as well. __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=675881 1972 C-10 SWB 1962 3/4 ton LWB 2011 GMC Sierra LML Z71 crewcab shortbed

07-26-2015, 05:36 PM	#12
BigSix Registered User Join Date: Mar 2014 Location: MD/VA/PA Or Inbetween Posts: 413	Re: Sources for "basic" heater? Thanks! The soft lines are completely missing. Removing that heater box from outside really opened up room for the twin turbos!

07-26-2015, 08:13 PM	#14
BigSix Registered User Join Date: Mar 2014 Location: MD/VA/PA Or Inbetween Posts: 413	Re: Sources for "basic" heater? It will only be awesome if I can get the plumbing to fit. Picture a bundle of snakes in a really small space. Thats about what its looking like.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.