Manual 465 to 90v20 Burb q's - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Jsfucttruck · 01-17-2018, 12:25 PM

So my friend wants to swap manual clutch setup, 465/205 into his 90 3/4 4x4 burb with a 400 and vss. I told him that I would love to help, but I have never done this swap. I have done the hydro swap and it was not too bad.

I am thinking the clutch linkage bracket could be the most pita thing to do. Any tips or pointers?I

**kwmech** · 01-17-2018, 01:23 PM

Pretty sure the square body still had mechanical linkage in 90. Find a truck with all the goodies under the dash and install.
what's going to happen to the existing transmission and t-case?

68Timber · 01-17-2018, 02:26 PM

I have that bracket. Let me find it and I can get some measurements for you. I don't think it would be hard to make from scratch.

Jsfucttruck · 01-17-2018, 08:43 PM

Quote:

Originally Posted by 68Timber

I have that bracket. Let me find it and I can get some measurements for you. I don't think it would be hard to make from scratch.

I appreciate it.

I have
465/205 early style
Pedal Assembly and Z bar linkage from pedal
a 78 k20 frame with a bracket and linkage
Early Flat trans crossmember and t case skid

He is offering up a 74 K20 350/465/205,with a Dana 44/14bff that runs and drives as a payment with current reg.

68Timber · 01-18-2018, 10:55 AM

I misunderstood, I thought you were missing the bracket. When you said it's going to be the worst part of the swap, you meant locating the bracket on the new frame?

v30crewcab · 01-18-2018, 07:24 PM

85 is first year of the hydro clutch.

Jsfucttruck · 01-19-2018, 01:08 AM

Quote:

Originally Posted by 68Timber

I misunderstood, I thought you were missing the bracket. When you said it's going to be the worst part of the swap, you meant locating the bracket on the new frame?

I have a bracket. I meant getting the bracket on. Would one have to lift the body off the frame a bit to drill the mounting holes?

Jsfucttruck · 01-17-2018, 08:35 PM

Quote:

Originally Posted by kwmech

Pretty sure the square body still had mechanical linkage in 90. Find a truck with all the goodies under the dash and install.
what's going to happen to the existing transmission and t-case?

I think the first yr for Hydro clutch for 83-84. I used a dually one as a donor for another swap. It was easier without the linkage.

The trans has no reverse. Not sure.

cal30_sniper · 03-18-2018, 01:30 PM

They would work fine if you ran the factory hydraulic clutch setup for that truck.

Jsfucttruck · 03-18-2018, 10:28 PM

Correct. He doesn't have the cash for it.

I found a whole 88 k5 donor, but he opted out.

He pays my time, so I let him decide. I tried to explain all the benefits. The blazer even had a tilt column and bench seat. It was mechanically sound with a rotten body. Guy was asking $1500. Even passed smog.

Jsfucttruck · 03-18-2018, 10:30 PM

The owner said the headers had holes in them so he had planned to change them out.

Manifolds are on order.

01-17-2018, 12:25 PM	#1
Jsfucttruck Registered User Join Date: Jul 2011 Location: Aptos Posts: 366	Manual 465 to 90v20 Burb q's So my friend wants to swap manual clutch setup, 465/205 into his 90 3/4 4x4 burb with a 400 and vss. I told him that I would love to help, but I have never done this swap. I have done the hydro swap and it was not too bad. I am thinking the clutch linkage bracket could be the most pita thing to do. Any tips or pointers?I

01-17-2018, 01:23 PM	#2
kwmech Senior Member Join Date: Mar 2003 Location: Colfax-California Posts: 8,635	Re: Manual 465 to 90v20 Burb q's Pretty sure the square body still had mechanical linkage in 90. Find a truck with all the goodies under the dash and install. what's going to happen to the existing transmission and t-case?

01-17-2018, 02:26 PM	#3
68Timber I know the pieces fit Join Date: Nov 2007 Location: MONTGOMERY, AL Posts: 5,523	Re: Manual 465 to 90v20 Burb q's I have that bracket. Let me find it and I can get some measurements for you. I don't think it would be hard to make from scratch. __________________ John 79 2wd Blazer (Bruiser) 85 M1009 Blazer (Sarge) build 74 Honda Z50 build

01-18-2018, 10:55 AM	#5
68Timber I know the pieces fit Join Date: Nov 2007 Location: MONTGOMERY, AL Posts: 5,523	Re: Manual 465 to 90v20 Burb q's I misunderstood, I thought you were missing the bracket. When you said it's going to be the worst part of the swap, you meant locating the bracket on the new frame? __________________ John 79 2wd Blazer (Bruiser) 85 M1009 Blazer (Sarge) build 74 Honda Z50 build

01-18-2018, 07:24 PM	#6
v30crewcab Registered User Join Date: Apr 2012 Location: Chatt Tn Posts: 982	Re: Manual 465 to 90v20 Burb q's 85 is first year of the hydro clutch. __________________ 88 military v30 crewcab shortbed 5.9 cummins, nv4500, 205 86 k30, 89 diesel burb, 76 gmc pathfinder 71 longbed 5.3 4l80 http://67-72chevytrucks.com/vboard/s...d.php?t=522535

03-18-2018, 01:30 PM	#9
cal30_sniper Registered User Join Date: Jan 2011 Location: Coastal NC Posts: 276	Re: Manual 465 to 90v20 Burb q's They would work fine if you ran the factory hydraulic clutch setup for that truck. __________________ 86 Chevrolet K20/30 Suburban - 8.1/NV4500/NP205/Dana 60/14 bolt FF, build in progress 73 Formula - 400/Doug Nash 4+1, resto on hold 86 Chevrolet K30 3+3 - 350/TH400/NP241, Air Force/Forest Service Rescue Truck, for sale 01 Ram 2500 - 5.9L Magnum, daily driver 91 BMW 325i - Chumpcar series racecar

03-18-2018, 10:28 PM	#10
Jsfucttruck Registered User Join Date: Jul 2011 Location: Aptos Posts: 366	Re: Manual 465 to 90v20 Burb q's Correct. He doesn't have the cash for it. I found a whole 88 k5 donor, but he opted out. He pays my time, so I let him decide. I tried to explain all the benefits. The blazer even had a tilt column and bench seat. It was mechanically sound with a rotten body. Guy was asking $1500. Even passed smog.

03-18-2018, 10:30 PM	#11
Jsfucttruck Registered User Join Date: Jul 2011 Location: Aptos Posts: 366	Re: Manual 465 to 90v20 Burb q's The owner said the headers had holes in them so he had planned to change them out. Manifolds are on order.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.