Anyone Have A Good Rebuildable Q'jet? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

69sixpackbee · 11-03-2003, 07:14 PM

For my '72 402. Just need a good rebuildable one. I will bush the throttle shafts so a little slop is okay. Prefer one that is complete.
Thanx!

smonty · 11-03-2003, 07:41 PM

I have one off my 72 1 ton that I replaced with a rebuilt one. You can have it for $25.00 plus shipping. Just let me know.

Ernie
smonty46@hotmail.com

**StingRay** · 11-03-2003, 08:33 PM

I have one for a 69 396, one for a 72 car 350 and another that is for a 71 350 truck.

Tx Firefighter · 11-03-2003, 10:11 PM

10 bucks plus shipping

69sixpackbee · 11-03-2003, 10:28 PM

Hey Smonty..what # is on the carb? Txfirefighter, that carb is too new. I need the divorced choke style. Looks good though

Stingray, how much for the truck one? I can always swap jets and rods from my existing one. That is the only real difference anyway between big and small block ones.
Where did the other poster go??

Breese · 11-03-2003, 11:30 PM

Hello..I have a Q-Jet that was a AC Delco rebuild for a 455 Buick. I took it apart for the jets and a couple other small odds and ends. Never been ran since AC rebuild. $50 plus shipping from Mo. Need #'s, PM me or leave post. Thanks

dion · 11-04-2003, 12:39 AM

I took it off because I don't know if it's for a 350 or a 400, I'm going to check the numbers tomorrow. I didn't want to try and sell before I knew exactly what is was.

*Phillip Johnson* · 11-04-2003, 02:17 AM

This one works.. It was off a 1970 350.. been sitting on the shelf for a year. Worked fine.
$50 plus shipping from 97527

pbjohnson2@aol.com

**StingRay** · 11-04-2003, 08:28 AM

I'll say 25 dollars plus shipping but let me find the carb # and check out the overall condition. I'll post later tonite.......if you haven't already found one by then. Q-jets are like belly buttons .....everbody has one

69sixpackbee · 11-04-2003, 12:56 PM

THANX ALL!!

**StingRay** · 11-04-2003, 10:06 PM

Either of these seem like they would be good builders. Both have fairly decent throttle shafts. The small block carb is so complete that it even has the choke rod. The tranny and throttle ball studs are not there. The small block carb I'd let go for 25. The 69 396 truck carb I'd need 75 for. Shipping from up here will cost a bit too!

Big block 7029214

**StingRay** · 11-04-2003, 10:07 PM

Small block #1

**StingRay** · 11-04-2003, 10:08 PM

Small block 7040511 pic #2

*Phillip Johnson* · 11-05-2003, 12:33 AM

Autozone here gets $50 just for a core charge

cheyenne10 · 11-05-2003, 12:41 AM

You might talk to these guys. I have bought 2 very nice rebuilds from them. They get $35 core for 402 carb.

www.carbsonly.com

ask for Carlos mention that you had talked with previous customer. They seem to want to please their customers, not all parts dealers are that way any more.

11-03-2003, 08:33 PM	#3
StingRay Senior Member Join Date: Mar 2000 Location: Saskatoon,SK,Canada Posts: 2,485	I have one for a 69 396, one for a 72 car 350 and another that is for a 71 350 truck. __________________ Saskatoon, Saskatchewan Canada

11-03-2003, 10:11 PM	#4
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	10 bucks plus shipping __________________ I'm on the Instagram- @Gearhead_Kevin

11-03-2003, 11:30 PM	#6
Breese Registered User Join Date: Oct 2003 Location: St.Louis, Mo. Posts: 174	Carb Hello..I have a Q-Jet that was a AC Delco rebuild for a 455 Buick. I took it apart for the jets and a couple other small odds and ends. Never been ran since AC rebuild. $50 plus shipping from Mo. Need #'s, PM me or leave post. Thanks

11-04-2003, 12:39 AM	#7
dion 72 Cheyenne Join Date: Oct 2001 Location: San Diego Posts: 2,086	that was me I took it off because I don't know if it's for a 350 or a 400, I'm going to check the numbers tomorrow. I didn't want to try and sell before I knew exactly what is was. __________________ Burnout Idle 1972Cheyenne 1966/67Stouts

11-04-2003, 02:17 AM	#8
Phillip Johnson Account Suspended Join Date: Apr 2000 Location: Grants Pass, Oregon Posts: 1,579	This one works.. It was off a 1970 350.. been sitting on the shelf for a year. Worked fine. $50 plus shipping from 97527 pbjohnson2@aol.com Attached Images Last edited by Phillip Johnson; 11-04-2003 at 02:20 AM.

11-03-2003, 07:14 PM	#1
69sixpackbee Registered User Join Date: Jan 2001 Location: Sabinal, Texas Posts: 1,706	Anyone Have A Good Rebuildable Q'jet? For my '72 402. Just need a good rebuildable one. I will bush the throttle shafts so a little slop is okay. Prefer one that is complete. Thanx!

11-03-2003, 07:41 PM	#2
smonty Smonty Join Date: Mar 2001 Location: Mesquite, TX, USA Posts: 769	Reply I have one off my 72 1 ton that I replaced with a rebuilt one. You can have it for $25.00 plus shipping. Just let me know. Ernie smonty46@hotmail.com __________________ 72 2WD Blazer 68 SWB Fleetside 67 SWB Stepside 2005 Chevy 1500HD Crewcab 56 Chris Craft Mahogany Runabout Looking for 36 Chevy 1/2 Ton P/U Project

11-03-2003, 10:28 PM	#5
69sixpackbee Registered User Join Date: Jan 2001 Location: Sabinal, Texas Posts: 1,706	Hey Smonty..what # is on the carb? Txfirefighter, that carb is too new. I need the divorced choke style. Looks good though Stingray, how much for the truck one? I can always swap jets and rods from my existing one. That is the only real difference anyway between big and small block ones. Where did the other poster go??

11-04-2003, 08:28 AM	#9
StingRay Senior Member Join Date: Mar 2000 Location: Saskatoon,SK,Canada Posts: 2,485	I'll say 25 dollars plus shipping but let me find the carb # and check out the overall condition. I'll post later tonite.......if you haven't already found one by then. Q-jets are like belly buttons .....everbody has one __________________ Saskatoon, Saskatchewan Canada

11-04-2003, 12:56 PM	#10
69sixpackbee Registered User Join Date: Jan 2001 Location: Sabinal, Texas Posts: 1,706	THANX ALL!!

11-04-2003, 10:06 PM	#11
StingRay Senior Member Join Date: Mar 2000 Location: Saskatoon,SK,Canada Posts: 2,485	Either of these seem like they would be good builders. Both have fairly decent throttle shafts. The small block carb is so complete that it even has the choke rod. The tranny and throttle ball studs are not there. The small block carb I'd let go for 25. The 69 396 truck carb I'd need 75 for. Shipping from up here will cost a bit too! Big block 7029214 Attached Images __________________ Saskatoon, Saskatchewan Canada

11-04-2003, 10:07 PM	#12
StingRay Senior Member Join Date: Mar 2000 Location: Saskatoon,SK,Canada Posts: 2,485	Small block #1 Attached Images __________________ Saskatoon, Saskatchewan Canada

11-04-2003, 10:08 PM	#13
StingRay Senior Member Join Date: Mar 2000 Location: Saskatoon,SK,Canada Posts: 2,485	Small block 7040511 pic #2 Attached Images __________________ Saskatoon, Saskatchewan Canada

11-05-2003, 12:33 AM	#14
Phillip Johnson Account Suspended Join Date: Apr 2000 Location: Grants Pass, Oregon Posts: 1,579	Autozone here gets $50 just for a core charge

11-05-2003, 12:41 AM	#15
cheyenne10 Senior Member Join Date: Apr 2000 Location: Oregon Posts: 2,512	BFIC rebuilders You might talk to these guys. I have bought 2 very nice rebuilds from them. They get $35 core for 402 carb. www.carbsonly.com ask for Carlos mention that you had talked with previous customer. They seem to want to please their customers, not all parts dealers are that way any more. __________________ Bob



Register or Log In To remove these advertisements.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.