|
|
|
06-06-2018, 09:07 AM
|
#1 |
|
Registered User
Join Date: Jun 2017
Location: Powder Springs, Ga
Posts: 50
|
A/C in a 63 with a l6
I'm looking into installing an AC unit in my 63 but all the aftermarket stuff recommends a v8. Anybody got any words of wisdom other than replacing the motor?
|
|
|
|
06-06-2018, 09:36 AM
|
#2 |
|
Moderator
  
Join Date: Aug 2011
Location: China Spring, TX
Posts: 7,280
|
Re: A/C in a 63 with a l6
Buy an AC Bracket for a 6 cylinder. The rest of the install is the same.
__________________
Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats? |
|
|
|
|
06-06-2018, 09:51 AM
|
#3 |
|
1965 Chevy C10, 2005 4.8L/4l60
 
Join Date: Aug 2004
Location: DFW Texas
Posts: 8,546
|
Re: A/C in a 63 with a l6
VA and OAP have brackets for what ever engine, call them.
__________________
Clyde65 Rebuild of Clyde http://67-72chevytrucks.com/vboard/s...84#post8338184 69 Aristocrat Lo Liner build http://67-72chevytrucks.com/vboard/s...84#post7561684  support our troops! |
|
|
|
|
06-06-2018, 12:31 PM
|
#4 |
|
Registered User
Join Date: Aug 2016
Location: Los Altos Hills, California
Posts: 170
|
Re: A/C in a 63 with a l6
|
|
|
|
|
06-06-2018, 05:52 PM
|
#5 |
|
Check The Champ, Demonstrator
Join Date: Jun 2009
Location: Montreal,Quebec
Posts: 6,627
|
Re: A/C in a 63 with a l6
The bracket for the original cigar type compressor is the same stamped steel version as the passenger car line. Hard to find . I found one for my 63 after many yeats of looking. Wish you better luck if you head that way. And then they'res the pulleys.
__________________
1963 Chevrolet Truck Literature LINK: https://picasaweb.google.com/113840717762774560215 YouTube Channel with 20+ Original Chevrolet Truck Salesmen, Mechanics & Service Department Training Slideshows. https://www.youtube.com/results?sear...otruk63&page=1 |
|
|
|
|
06-07-2018, 12:45 AM
|
#6 |
|
Registered User
Join Date: Mar 2018
Location: Florence Ms
Posts: 117
|
Re: A/C in a 63 with a l6
I installed a Vintage Air unit in my six cylinder 63 C10. When I ordered the unit I specified vehicle and engine and the unit includes the proper bracket and everything needed for installation except pulley. I think I got the dual groove pulley from Speedway. The only other thing I added was a larger aluminum radiator as I thought the original in the truck was a little small.
Unit works great and no problems with it working with the six cylinder. In Mississippi, cold air is required for my better half to cruise with me. |
|
|
|
|
06-07-2018, 05:39 AM
|
#7 |
|
Registered User
Join Date: Jun 2017
Location: Powder Springs, Ga
Posts: 50
|
Re: A/C in a 63 with a l6
Great looking set up. What pulley did you use on the crank?
|
|
|
|
|
06-07-2018, 02:16 PM
|
#8 |
|
Registered User
Join Date: Dec 2007
Location: N Texas
Posts: 580
|
Re: A/C in a 63 with a l6
Msgt,
I too highly recommend Vintage Air, and for you to call Vintage Air. The Davis setup is probably easy and straightforward, but doesn't look OEM or Custom if you care about the look too. I am using an old Vintage Air bracket for a Sanden compressor, but I don't see it in their online catalog anymore--but you can't trust that--call them! I do see the plate steel brackets to weld up your own, they are part # 151015 -Universal fabricator’s bracket for Sanden compressor Railroader, do you have the part number for your bracket?
__________________
292 + TKO500 |
|
|
|
|
06-07-2018, 02:29 PM
|
#9 |
|
Registered User
Join Date: Dec 2007
Location: N Texas
Posts: 580
|
Re: A/C in a 63 with a l6
[ATTACH][/ATTACH]This is my setup using a Sanden and modified Vintage Air bracket. I had to cut and weld to adjust a little for belt alignment. I am a 292 running a 3 groove harmonic balancer. I fabbed a mount for the alternator and GM II power steering pump low on the drivers side.
__________________
292 + TKO500 |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
