How did this happen?

[vet57air]

I installed my rear window and it looked great.... for several weeks. Then this happened. It appears to have puckered and pulled away from the glass on top. Any ideas? I have bought a new gasket and lock strip but would like to understand what happened so it doesn't happen again. Couldn't get the image to be correct but the pucker is on the bottom flat.

[Steeveedee]

Won't know why until it's out, but it is probably split. Is the stainless trim new, as well as the gasket?

[vet57air]

Originally Posted by Steeveedee

Won't know why until it's out, but it is probably split. Is the stainless trim new, as well as the gasket?

Yes, gasket and trim were new. Guess we will see if its split when i take it out.
Thx

[SCOTI]

Not sure what causes the issue.

I rotated the image to get a better view for for those that might be able to answer.

[vet57air]

Originally Posted by SCOTI

Not sure what causes the issue.

I rotated the image to get a better view for for those that might be able to answer.

Thank you. Looking at the new lock strip I notice a piece of trim I didn't get before. I can't find any info on how it goes in but might look better than just butting the trim together.

[mongocanfly]

I was gonna say its probably split between the inner and outer face..but Steve beat me to it

[mongocanfly]

thats the trim piece that goes over the meeting ends of the lock strip..it goes in the seal over the lock strip

[vet57air]

Originally Posted by mongocanfly

thats the trim piece that goes over the meeting ends of the lock strip..it goes in the seal over the lock strip

Does it go in last after the lock strip is installed?

[mongocanfly]

yep...2:26 and 11:45 shows how it comes out and goes in
https://www.youtube.com/watch?v=ufZW2CnhOS0

[vin63]

As a couple of the others mentioned earlier, it might be that the seal cut/tore while putting in the lock strip (for the rear window, I hope the lock strip wasn't steel). My friend's rear seal did that a few years back and when we removed the glass and seal, it was indeed split inside at that area and started to pull away.

When installing the lock strip, be sure to spray generous amounts of the lubricant solution of your preference (I used an old spray bottle with a water dishsoap solution) as you install the lock strip, and don't be too aggressive with the lock strip tool as you insert the strip. I have not seen a rear window lock strip with that center trim piece.

http://www.youtube.com/watch?v=-80P7IXd0EU

[vet57air]

Originally Posted by vin63

As a couple of the others mentioned earlier, it might be that the seal cut/tore while putting in the lock strip (for the rear window, I hope the lock strip wasn't steel). My friend's rear seal did that a few years back and when we removed the glass and seal, it was indeed split inside at that area and started to pull away.

When installing the lock strip, be sure to spray generous amounts of the lubricant solution of your preference (I used an old spray bottle with a water dishsoap solution) as you install the lock strip, and don't be too aggressive with the lock strip tool as you insert the strip. I have not seen a rear window lock strip with that center trim piece.

http://www.youtube.com/watch?v=-80P7IXd0EU

I have never seen a center trim piece on our trucks either for the rear window. Lock strip is the chromed plastic type. Next week I plan to take out the rear window and reinstall.

[The Rocknrod]

Originally Posted by vin63

... I have not seen a rear window lock strip with that center trim piece.

Neither have I.

[mongocanfly]

My 81 has them on the back, but theres one on each side lower corner..its L shaped
The front has a single like you showed, bottom center of windshield..

[vet57air]

Pulled out the lock strip and can see what happened. There is a tare in the weatherstrip. Factory flaw or possibly did it with the lock strip tool. Ready to reinstall with new weatherstrip.