Boyds Tank Problems in a '60 SWB

[Too Slow '90]

I started the installation last weekend and was pretty optimistic until I set it in place. I removed the crossmember and set it in place. You can see from the pictures that I cut a small relief in the bed support for the roll over vent. In this location the flush fill cap will not fit. If I move it forward the roll over vent and sender will hit the bed support and the EFI cap will be under it. The fill cap is supposed to be in the middle of one of the boards but it hits dead center of the stainless steel bed strips.

It is supposed to be correct so and I'm wondering if anyone else had these problems. I have not received a response from Boyds.

[Mack B]

I had similar issues on my 63. My filler didn’t center a strip but did overlap one. I also had to cut the nipple on the filler down. I bought the tank in 2013 but didn’t install till 2 years ago, I assumed mine was made before some changes where made.

[Too Slow '90]

Mine is only a year and a half old. Everything I read and discussed with Boyd indicated it was the correct one. If I don't hear from them soon I may just have to take it to a local shop and have them move the filler. I can probably modify the other parts to make it work but I don't want to cut the bed strips.

[PGSigns]

I think the tank is to far back. The three I have done I removed the small cross member that is in front of your tank and left the rear one in to protect the tank. The bed rail is in between the vents and the filler. This will be more important if you put an efi pump where the plate is.
Jimmy

[Too Slow '90]

Originally Posted by PGSigns

I think the tank is to far back. The three I have done I removed the small cross member that is in front of your tank and left the rear one in to protect the tank. The bed rail is in between the vents and the filler. This will be more important if you put an efi pump where the plate is.
Jimmy

I appreciate the response. My next step was to move it forward and see what the next conflicts are. I think I can crank the vent down and clear the bed support. The filler is going to split the bed strip no matter how I position it so I will have it moved by someone local. I didn't get any response from Boyd welding. I guess it's a sign of the times.

[oldtrux]

Maybe these pics could help?

[verdell]

Originally Posted by oldtrux

Maybe these pics could help?

60-62 has a different frame than 63-66. The Boyd's tank for the 60-62 is 8 inches wider than the 63-66 tank as well according to their specs. I'm currently running a 94 S10 blazer tank in my 60 and had to get creative with the filler. I was interested in the Boyd's tank for my 60 but now I'm not so sure...

[oldtrux]

Oh my bad,didn’t know that!

[forestb]

Originally Posted by verdell

60-62 has a different frame than 63-66. The Boyd's tank for the 60-62 is 8 inches wider than the 63-66 tank as well according to their specs. I'm currently running a 94 S10 blazer tank in my 60 and had to get creative with the filler. I was interested in the Boyd's tank for my 60 but now I'm not so sure...

The tanks are wider but the cross sills are in the same location. Can you move it forwards so that the cross sill goes across the center of the tank? I know when I installed mine on my 62 that is what I did but that then caused issues with bolting it to the frame because if you move it too far forward the frame is boxed where you need to bolt it. I had to get creative with the bracket that is supposed to go inside the frame. I think I had to chop it up and put part of it inside the boxed section.

[MT65]

Seems to me it was poorly engineered, some are posting about similar issues, the fact that they are not responding speaks volumes, they could care less, they have your money and they have no dignity…
Your at a point to fix it, sad news I’m sure , but make it what you need it to be, more dollars, but doable.
This is exactly why I have a local guy build my “vessels”, I make a pattern, make the fuel pump and sender plates, tell him where the filler should be and have zero issues, probably less money involved than what you already spent
Sorry your having this issue, but I see more and more of this in the aftermarket industry today….

[oldtrux]

Maybe these pics could help?

[oldtrux]

Is my filler a little further from frame rail?