64-66 Windshield Molding Joint Clips? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

66c10Steve · 03-28-2023, 04:20 PM

Hey folks!

This is a long shot but does anyone know of a supplier that I could purchase just the joint clips instead of the entire windshield trim kit?

I'm really hoping I can find 2 or all 4 instead of buying this whole set:

https://www.classicparts.com/1964-66...ctinfo/62-024/

The previous owner must have lost two when they dismantled the truck....

Thanks in advance.

**chev-obsession** · 04-04-2023, 01:49 AM

I’m looking for one of these as well, curious if clips from another vehicle interchange
Posted via Mobile Device

**SOON2BLAZE** · 11-30-2023, 12:42 AM

Looking for two of theses as well. Any one know if 67-72 clips might work?

theastronaut · 11-30-2023, 10:55 AM

I'm working on dies to make the clips, should have them available in a few weeks. Already have .017" pre-polished stainless ready for when the dies are finished.

**SOON2BLAZE** · 11-30-2023, 12:53 PM

Yes! Thank you for making these.

dbchevy65 · 12-08-2023, 11:51 PM

Following

03-28-2023, 04:20 PM	#1
66c10Steve Registered User Join Date: Jul 2019 Location: Cambridge, Ontario Posts: 34	64-66 Windshield Molding Joint Clips? Hey folks! This is a long shot but does anyone know of a supplier that I could purchase just the joint clips instead of the entire windshield trim kit? I'm really hoping I can find 2 or all 4 instead of buying this whole set: https://www.classicparts.com/1964-66...ctinfo/62-024/ The previous owner must have lost two when they dismantled the truck.... Thanks in advance. Attached Images __________________ Check out my 66 C10 build here: http://67-72chevytrucks.com/vboard/s...d.php?t=546694 Look here, I also built a canoe: http://stevescedarstripcanoe.blogspot.com/

04-04-2023, 01:49 AM	#2
chev-obsession Senior Member Join Date: Jul 2008 Location: kennewick, WA Posts: 1,513	Re: 64-66 Windshield Molding Joint Clips? I’m looking for one of these as well, curious if clips from another vehicle interchange Posted via Mobile Device

11-30-2023, 12:42 AM	#3
SOON2BLAZE Account Suspended Join Date: Aug 2005 Location: Southern UT Posts: 906	Re: 64-66 Windshield Molding Joint Clips? Looking for two of theses as well. Any one know if 67-72 clips might work?

11-30-2023, 10:55 AM	#4
theastronaut Registered User Join Date: May 2011 Location: Anderson SC Posts: 3,901	Re: 64-66 Windshield Molding Joint Clips? I'm working on dies to make the clips, should have them available in a few weeks. Already have .017" pre-polished stainless ready for when the dies are finished. __________________ Project Goldilocks '66 C10 Short Fleet BBW Build '65 C10 Highly Detailed Stock Restoration Thread '78 Camaro Targa Roof Build '55 International Metal/Body/Paint Work '66 F100 Full Rotisserie Restoration '40 Packard 120 Convertible Coupe Restoration How To Restore and Detail an Original Gauge Cluster How To Detail Sand Body Panels, Edges, Corners, Etc

11-30-2023, 12:53 PM	#5
SOON2BLAZE Account Suspended Join Date: Aug 2005 Location: Southern UT Posts: 906	Re: 64-66 Windshield Molding Joint Clips? Yes! Thank you for making these.

12-08-2023, 11:51 PM	#6
dbchevy65 Registered User Join Date: May 2013 Location: North highlands ca Posts: 79	Re: 64-66 Windshield Molding Joint Clips? Following

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.