|
|
|
05-01-2004, 06:00 PM
|
#2 |
|
Registered User
Join Date: Mar 2004
Location: Virginia beach, Va
Posts: 209
|
hmmm...not to sure dude, check and see who had gone from a 72 and convereted it to the 73-87. possibly the same concept.
__________________
~Christopher L. Orr 71 c20, 454- Stolen While Deployed. dynoed at 550 ft lbs, 425 hp at 3000 rpm (mustang dyno). TH400 3500 stall.... etc, etc. |
|
|
|
05-02-2004, 12:18 PM
|
#3 |
|
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,402
|
Yes , you can swap it. you should be able to bolt the complete eng cradle under the truck with only a couple holes to adjust(egg out). You can also swap the lower a arms, with balljoints,the spindles, & upper balljoints onto the exsisting crossmember. the outer tierod ends will also be different(probably easier to use the center link,tierods, ect from the 72). good luck,crazyL
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
|
|
|
|
05-02-2004, 01:39 PM
|
#5 |
|
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,402
|
Yup, thats it in the pic....good luck,crazyL
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
|
|
|
|
05-02-2004, 02:17 PM
|
#6 |
|
Registered User
Join Date: Apr 2004
Location: Las Vegas
Posts: 225
|
there are 7 bolts on each side of the member.....which ones have to be "persuaded" b/c i would rather just put my notched member on the 3/4 ton and make it a 1/2 ton and slam it at the same time
|
|
|
|
|
05-02-2004, 04:22 PM
|
#7 |
|
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,402
|
I have a 77 crossmember to notch & swap into my 69.....but havent done it yet. I have been told that 1 bolt on ea side of the frame is the offender(not sure which one, but the bottom 3 on ea side line up. when you set it up, post your findings to give this old man a "heads up". good luck,crazyL
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
|
|
|
 |
| Bookmarks |
|
|
Hybrid Mode
