How do you remove the door latch assembly? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

70c10 · 10-09-2004, 07:42 PM

I need to buy and replace a door latch assembly for a passenger door but I don't know how to remove the old one. I removed the 3 screws on the end of the door but don't know how to get the unit past the window channel. Any help would be appreciated. Thanks

gonebad2 · 10-09-2004, 09:00 PM

Unbolt the weatherstrtip channel ( two 1/4-20 phillips head screws under the door panel and one 7/16" head 1/4 20 bolt on the outside of the door shell. Pull it forward a little bit. It will give you the room you need to get it out. Tip: Re-attach the actuator rods to the new door latch assy BEFORE you bolt it in place. It's a real pain to try and connect them when it's bolted in place.

70c10 · 10-09-2004, 11:56 PM

Thanks. I'll give it a shot tomorrow. I remember seeing 2 screws but don't recall seeing the bolt.

MOTHERTRUCKERS · 10-10-2004, 08:44 AM

The bolt is a phillips screw like the others but has a larger flat washer and not the star washer. be careful with the linkage clips they get lost or broken easily.

gonebad2 · 10-10-2004, 02:22 PM

Mothertruckers is right......The bolt on the outside of the door shell IS a phillips head with a washer attached....Sorry for the bad info.

70c10 · 10-10-2004, 07:43 PM

Thanks guys. So far I removed the 3 phillips screws. Does the linkage rod just pop up out of the clips?. Ed, I PM'd you about the latch. I hope you got it because I need it ASAP!

10-09-2004, 07:42 PM	#1
70c10 67-72 Addict! Join Date: Feb 2002 Location: The TAX State! Posts: 7,856	How do you remove the door latch assembly? I need to buy and replace a door latch assembly for a passenger door but I don't know how to remove the old one. I removed the 3 screws on the end of the door but don't know how to get the unit past the window channel. Any help would be appreciated. Thanks __________________ Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads

10-09-2004, 09:00 PM	#2
gonebad2 Merciless Butcher Join Date: Oct 2003 Location: CC Nevada Posts: 1,447	Unbolt the weatherstrtip channel ( two 1/4-20 phillips head screws under the door panel and one 7/16" head 1/4 20 bolt on the outside of the door shell. Pull it forward a little bit. It will give you the room you need to get it out. Tip: Re-attach the actuator rods to the new door latch assy BEFORE you bolt it in place. It's a real pain to try and connect them when it's bolted in place. __________________ Your Bought And Sold....I Got Your Soul!

10-09-2004, 11:56 PM	#3
70c10 67-72 Addict! Join Date: Feb 2002 Location: The TAX State! Posts: 7,856	Thanks. I'll give it a shot tomorrow. I remember seeing 2 screws but don't recall seeing the bolt. __________________ Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads

10-10-2004, 08:44 AM	#4
MOTHERTRUCKERS Registered User Join Date: Dec 1999 Location: BRADENTON FLA Posts: 3,269	The bolt is a phillips screw like the others but has a larger flat washer and not the star washer. be careful with the linkage clips they get lost or broken easily. __________________ Rest in Peace Ed. Thanks for all the good times.

10-10-2004, 02:22 PM	#5
gonebad2 Merciless Butcher Join Date: Oct 2003 Location: CC Nevada Posts: 1,447	Mothertruckers is right......The bolt on the outside of the door shell IS a phillips head with a washer attached....Sorry for the bad info. __________________ Your Bought And Sold....I Got Your Soul!

10-10-2004, 07:43 PM	#6
70c10 67-72 Addict! Join Date: Feb 2002 Location: The TAX State! Posts: 7,856	Thanks guys. So far I removed the 3 phillips screws. Does the linkage rod just pop up out of the clips?. Ed, I PM'd you about the latch. I hope you got it because I need it ASAP! __________________ Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.