|
|
|
07-29-2005, 02:16 AM
|
#1 |
|
Foom, foom, foom!
 
Join Date: Mar 2005
Location: Abilene, TX
Posts: 106
|
Timing
I know this may be kinda if a dumb question but, How can you chack your timing with a timing light if there is no marker on you Harmonic balancer?
How can I figure out where to mark the balancer to tell me when #1 cylinder is firing?
__________________
- Dan 84' LWB C10 // 2.5" from collector back. duel Turbo Mufflers // 350 w/ TH350 long Headers//3.73 rearend gears Future Mods 3/4 suspension drop 
|
|
|
|
07-29-2005, 02:27 AM
|
#2 |
|
Right turn Clyde
Join Date: Nov 2002
Location: Cincinnati, Ohio
Posts: 2,911
|
Have you checked the balancer for a groove? It could be covered in grease. What year is the block, is the balancer new?
Do you have a Piston stop that uses a sparkplug adapter to install into the cylinder head?
__________________
1974 C25 LWB: 454 4bbl Carb / TH400 / 3.73 1992 Camaro RS 305 TBI Last edited by MylilBowTie; 07-29-2005 at 02:28 AM. |
|
|
|
|
07-29-2005, 03:43 AM
|
#3 |
|
Gettin It One Pice At A Time
Join Date: Oct 2004
Location: everett, washington
Posts: 2,688
|
if it is covered in grease and what not. what do you do to make it show up better? mine is the same color as the h/b and hard to see when spining 800 rpms
__________________
RIP ELJAY   Work In Progress 1979 GMC C1500 Trailering Special. Getting the truck done, one piece at a time. “You can tell a lot about a fellow’s character by his way of eating jellybeans.”Ronald Reagan “I don’t know the key to success but I know the key to failure is trying to please everybody.” Bill Cosby |
|
|
|
|
07-29-2005, 03:53 AM
|
#4 |
|
Right turn Clyde
Join Date: Nov 2002
Location: Cincinnati, Ohio
Posts: 2,911
|
I would degrease it then mark it. Bump the balancer groove to the bottom so its easier to clean and mark. You can use chalk you can get an paint pen you can mask the grove off on both sides leaving a very small slit and spray paint it or brush. White, Silver, Neon yellow. Really depends on what color it is.
Probably wouldn't hurt to clean up the timing tab either. Long screwdriver and a shop rag will get it most times.
__________________
1974 C25 LWB: 454 4bbl Carb / TH400 / 3.73 1992 Camaro RS 305 TBI Last edited by MylilBowTie; 07-29-2005 at 03:54 AM. |
|
|
|
|
07-29-2005, 08:10 AM
|
#5 |
|
Foom, foom, foom!
Join Date: Mar 2005
Location: Abilene, TX
Posts: 106
|
thanks seems like I'm not the only one with these problems..
__________________
- Dan 84' LWB C10 // 2.5" from collector back. duel Turbo Mufflers // 350 w/ TH350 long Headers//3.73 rearend gears Future Mods 3/4 suspension drop
|
|
|
|
|
07-29-2005, 01:28 PM
|
#6 |
|
Stepsides RULE
Join Date: Jul 2004
Location: Pineville, LA
Posts: 1,921
|
Liquid paper. Make a mark
__________________
1981 Chevy C10 Custom Deluxe Stepside 350 V8, headers, side exhausts, 3-speed auto SOLD 1980 Chevy C10 Custum Deluxe Stepside 305 V8, Edelbrock Performer Intake, Edelbrock 1406 600CFM 4-barrel, TH350C. Bent rod. SOLD 1984 GMC Sierra Classic Longbed 6.2L Diesel SOLD 2009 Kawasaki KLX-250S too many mods for this signature 1999 Honda Accord EX 4-cylinder, 17" Motegi Wheels 215/45/17 Sumitomo tires, Tein S-Tech lowering springs, KYB GR2 shocks, Acura TL 20mm rear swaybar, debadged, blackhoused headlights, Short-Ram Intake Cardomain of the Accord |
|
|
|
 |
| Bookmarks |
|
|
Hybrid Mode
