WTB np205 and other parts - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**smokinn** · 12-27-2005, 05:40 PM

Ok what I really need is the rear drive shaft for a np205 transfer case. That will fit a 77 SB 350 4x4 with a 350 tranny. I have everything else just need the rear drive shaft.

Jason

*bisquik65* · 12-27-2005, 08:38 PM

Do you have a bolt on yoke...on the case or slip yoke...And a th350/205 is a rare setup...

Also a weld to weld measurment would help too

**smokinn** · 12-27-2005, 08:53 PM

Quote:

Originally Posted by bisquik65

is a rare setup...

Why is it rare? A 205 is a pt transfer case. A 203 is a full time transfer case. Thats whats in it now is a 203. I want to get rid of the FT and put in PT. I know they make a conversion kit for the FT to PT. Has to do with swapping gears but I dont think its a good route. Cheaper but I cant see how it can be better.

Jason

*bisquik65* · 12-27-2005, 08:58 PM

Quote:

Originally Posted by smokinn

Why is it rare? A 205 is a pt transfer case. A 203 is a full time transfer case. Thats whats in it now is a 203. I want to get rid of the FT and put in PT. I know they make a conversion kit for the FT to PT. Has to do with swapping gears but I dont think its a good route. Cheaper but I cant see how it can be better.

Jason

You may want to go to the faq's section on the board...over this swap...It is not a direct bolt on....Or try the 4x4 discussion...board.. And the adapters are different,mounts are different...Just trying to help,Thanks,Erick

**smokinn** · 12-27-2005, 09:58 PM

Eric,

I know your trying to help as this swap is new to me. Do you think the conversion kit would be a better route?

Jason

67-72williso · 12-27-2005, 10:22 PM

Putting lockouts on the hubs will help. NP-203 trucks didn`t have lockouts on the front, so the front drive shaft turned all the time (full time). Hope this helps.
Later Willis

T_Dilley · 01-03-2006, 08:34 PM

Whats the length on the driveshaft?

12-27-2005, 05:40 PM	#1
smokinn Senior Member Join Date: Aug 2002 Location: omaha,Ne Posts: 617	WTB np205 and other parts Ok what I really need is the rear drive shaft for a np205 transfer case. That will fit a 77 SB 350 4x4 with a 350 tranny. I have everything else just need the rear drive shaft. Jason

12-27-2005, 08:38 PM	#2
bisquik65 Account Suspended Join Date: Apr 2004 Location: N.C. high country Posts: 6,107	Re: WTB np205 and other parts Do you have a bolt on yoke...on the case or slip yoke...And a th350/205 is a rare setup... Also a weld to weld measurment would help too Last edited by bisquik65; 12-27-2005 at 08:39 PM.

12-27-2005, 09:58 PM	#5
smokinn Senior Member Join Date: Aug 2002 Location: omaha,Ne Posts: 617	Re: WTB np205 and other parts Eric, I know your trying to help as this swap is new to me. Do you think the conversion kit would be a better route? Jason

12-27-2005, 10:22 PM	#6
67-72williso Junk/Daily Driver Club Join Date: Feb 2004 Location: Manheim, PA 17545 Posts: 253	Re: WTB np205 and other parts Putting lockouts on the hubs will help. NP-203 trucks didn`t have lockouts on the front, so the front drive shaft turned all the time (full time). Hope this helps. Later Willis __________________ Daily Driver: 1970 C-20 400 sbc,sm-465,Dana 61 one ton SRW rear, 3.07 gears, locker. There are three kinds of people: those who make things happen, those who watch things happen, and those who have no idea what happened!

01-03-2006, 08:34 PM	#7
T_Dilley Can't tell me nothin' Join Date: Nov 2004 Location: Pana, IL Posts: 250	Re: WTB np205 and other parts Whats the length on the driveshaft?



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.