Transfer Case Support ? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Baketown Scotty** · 06-22-2006, 04:41 PM

Can someone post a picture showing the support for the transmission / transfer case (700R4 and NP208)? Originally had a 4 speed manual and I am using the original cross member. I made a couple of brackets but not quite sure I'm on the right track. Unable to upload (attach) picture, message says it is too big.

LUV2XCLR8 · 06-22-2006, 05:11 PM

E-mail me your pic's and I will post them - luv2xclr8@charter.net
or .............. check our FAQ's section on how to post pictures

vtblazer · 06-23-2006, 07:00 AM

Quote:

Originally Posted by Baketown Scotty

Can someone post a picture showing the support for the transmission / transfer case (700R4 and NP208)? Originally had a 4 speed manual and I am using the original cross member. I made a couple of brackets but not quite sure I'm on the right track. Unable to upload (attach) picture, message says it is too big.

Try posting the same question on the later years trucks section, they would have that combo in their thrucks from the factory.

The only thing we'd have to show you (stock) would be either a
th-350/205 or th-400/205 combo.

to the board, enjoy the ride.

**Gary 70 Jimmy** · 06-23-2006, 08:31 AM

Heres a picture I have if you need more pictures i can take more

**Baketown Scotty** · 06-23-2006, 11:10 AM

Gary - Mind if I send you a picture and get your opinion?

**Gary 70 Jimmy** · 06-23-2006, 04:39 PM

Ok send me your picture I will post it if you want. knigamy@netzero.com

LUV2XCLR8 · 06-24-2006, 04:12 PM

Here are his pic's

**Gary 70 Jimmy** · 06-26-2006, 08:35 AM

wow that thing is up their dont look like it be very sturdy do you have the side mount on transfer case dont see it in your pictures.

**Baketown Scotty** · 06-26-2006, 01:11 PM

I do not have the side mount installed. I have a rod attached to the two bolts for the side mount. The rod extends up to a bolt holding transmission to engine. It looks like it will be in the way of the exhaust when I get ready to install it. I will probably have to get rid of the rod and re-install the side mount. The side mount I have is from the original transfer case (205?).

Gary 70 - Can you post a picture of yours from the front showing the supports from the cross member up?

LUV2XCLR8 · 06-26-2006, 05:34 PM

Can you use the same support you have, minus the upper supports, but
bolt the bottom section to where the top supports were, did that make
any sense, I can't do photoshop or I would, or am I making no sense

**Baketown Scotty** · 06-26-2006, 05:41 PM

It took me a minute but I think I follow. That may be the ticket. I'll have to check to be sure the front driveshaft will not be blocked.

LUV2XCLR8 · 06-26-2006, 05:55 PM

Quote:

Originally Posted by Baketown Scotty

It took me a minute but I think I follow. That may be the ticket. I'll have to check to be sure the front driveshaft will not be blocked.

If it's close maybe try using a trick c-notch job on the crossmember

**Gary 70 Jimmy** · 06-27-2006, 11:19 AM

I will take a picture when ever it stops raining

**Baketown Scotty** · 06-27-2006, 02:26 PM

LUV - I was hoping I wouldn't have to take the body off again. I do appreciate your help.

Gary 70 - Look forward to the pictures. I do not miss that humidity, I grew up off I-70 in IN.

06-22-2006, 04:41 PM	#1
Baketown Scotty Junior Member Join Date: Oct 2005 Location: Bakersfield, CA Posts: 317	Transfer Case Support ? Can someone post a picture showing the support for the transmission / transfer case (700R4 and NP208)? Originally had a 4 speed manual and I am using the original cross member. I made a couple of brackets but not quite sure I'm on the right track. Unable to upload (attach) picture, message says it is too big.

06-22-2006, 05:11 PM	#2
LUV2XCLR8 The LuvShack Garage Join Date: Jan 2004 Location: Maple Grove, TN (West Side) Posts: 30,468	Re: Transfer Case Support ? E-mail me your pic's and I will post them - luv2xclr8@charter.net or .............. check our FAQ's section on how to post pictures __________________ Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T

06-23-2006, 08:31 AM	#4
Gary 70 Jimmy Senior Member Join Date: Jan 2002 Location: Burghill, Ohio 44404 Posts: 3,401	Re: Transfer Case Support ? Heres a picture I have if you need more pictures i can take more Last edited by Gary 70 Jimmy; 10-24-2008 at 09:14 AM.

06-23-2006, 11:10 AM	#5
Baketown Scotty Junior Member Join Date: Oct 2005 Location: Bakersfield, CA Posts: 317	Re: Transfer Case Support ? Gary - Mind if I send you a picture and get your opinion?

06-23-2006, 04:39 PM	#6
Gary 70 Jimmy Senior Member Join Date: Jan 2002 Location: Burghill, Ohio 44404 Posts: 3,401	Re: Transfer Case Support ? Ok send me your picture I will post it if you want. knigamy@netzero.com

06-24-2006, 04:12 PM	#7
LUV2XCLR8 The LuvShack Garage Join Date: Jan 2004 Location: Maple Grove, TN (West Side) Posts: 30,468	Re: Transfer Case Support ? Here are his pic's Attached Images __________________ Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T

06-26-2006, 08:35 AM	#8
Gary 70 Jimmy Senior Member Join Date: Jan 2002 Location: Burghill, Ohio 44404 Posts: 3,401	Re: Transfer Case Support ? wow that thing is up their dont look like it be very sturdy do you have the side mount on transfer case dont see it in your pictures.

06-26-2006, 01:11 PM	#9
Baketown Scotty Junior Member Join Date: Oct 2005 Location: Bakersfield, CA Posts: 317	Re: Transfer Case Support ? I do not have the side mount installed. I have a rod attached to the two bolts for the side mount. The rod extends up to a bolt holding transmission to engine. It looks like it will be in the way of the exhaust when I get ready to install it. I will probably have to get rid of the rod and re-install the side mount. The side mount I have is from the original transfer case (205?). Gary 70 - Can you post a picture of yours from the front showing the supports from the cross member up?

06-26-2006, 05:34 PM	#10
LUV2XCLR8 The LuvShack Garage Join Date: Jan 2004 Location: Maple Grove, TN (West Side) Posts: 30,468	Re: Transfer Case Support ? Can you use the same support you have, minus the upper supports, but bolt the bottom section to where the top supports were, did that make any sense, I can't do photoshop or I would, or am I making no sense Attached Images __________________ Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T

06-26-2006, 05:41 PM	#11
Baketown Scotty Junior Member Join Date: Oct 2005 Location: Bakersfield, CA Posts: 317	Re: Transfer Case Support ? It took me a minute but I think I follow. That may be the ticket. I'll have to check to be sure the front driveshaft will not be blocked.

06-27-2006, 11:19 AM	#13
Gary 70 Jimmy Senior Member Join Date: Jan 2002 Location: Burghill, Ohio 44404 Posts: 3,401	Re: Transfer Case Support ? I will take a picture when ever it stops raining

06-27-2006, 02:26 PM	#14
Baketown Scotty Junior Member Join Date: Oct 2005 Location: Bakersfield, CA Posts: 317	Re: Transfer Case Support ? LUV - I was hoping I wouldn't have to take the body off again. I do appreciate your help. Gary 70 - Look forward to the pictures. I do not miss that humidity, I grew up off I-70 in IN.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.