Carb piecs, supplier source someone?? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

dougs69c10 · 06-23-2006, 08:45 PM

I have a 250 inliner and I got done putting a new carb on it, well as I was attatching the linkage to the carb, I had a piece break.

The piece that broke is an arm that comes off the carb's arm and attaches to the ball on the large pivot piece that attaches to the manifold.

The piece in question is maybe 3 inches long, 3/8 around and had an almost 90* bend at the end where it hooks to the carb. The socket at the end broke, is that a piece I can get somewhere or do I need to start footin through junk yards

mbgmike · 06-23-2006, 09:11 PM

I am sure I have a used one. I can look tomorrow at the shop. I don't know of anyone off hand that sells them I reread your post and I assume you are putting a stock carb on?

dougs69c10 · 06-23-2006, 09:32 PM

yeah stock rochester 1 barrell

mbgmike · 06-24-2006, 09:36 AM

I found one. pm me with address if you want it. Free but shipping will run $50.00

just kidding. Let me know if you find anyone who sells them new. I never have.

mbgmike · 06-28-2006, 06:27 AM

part sent monday

06-23-2006, 08:45 PM	#1
dougs69c10 Registered User Join Date: Feb 2006 Location: Birmingham,Alabama Posts: 260	Carb piecs, supplier source someone?? I have a 250 inliner and I got done putting a new carb on it, well as I was attatching the linkage to the carb, I had a piece break. The piece that broke is an arm that comes off the carb's arm and attaches to the ball on the large pivot piece that attaches to the manifold. The piece in question is maybe 3 inches long, 3/8 around and had an almost 90* bend at the end where it hooks to the carb. The socket at the end broke, is that a piece I can get somewhere or do I need to start footin through junk yards __________________ 1969 c10 stepside 250 inline six, 4speed granny tranny, 4.11 posi rear end

06-23-2006, 09:11 PM	#2
mbgmike Registered User Join Date: Aug 2005 Location: Pasadena,Tx /Pto Pta DR Posts: 5,415	Re: Carb piecs, supplier source someone?? I am sure I have a used one. I can look tomorrow at the shop. I don't know of anyone off hand that sells them I reread your post and I assume you are putting a stock carb on? Last edited by mbgmike; 06-23-2006 at 09:12 PM.

06-23-2006, 09:32 PM	#3
dougs69c10 Registered User Join Date: Feb 2006 Location: Birmingham,Alabama Posts: 260	Re: Carb piecs, supplier source someone?? yeah stock rochester 1 barrell __________________ 1969 c10 stepside 250 inline six, 4speed granny tranny, 4.11 posi rear end

06-24-2006, 09:36 AM	#4
mbgmike Registered User Join Date: Aug 2005 Location: Pasadena,Tx /Pto Pta DR Posts: 5,415	Re: Carb piecs, supplier source someone?? I found one. pm me with address if you want it. Free but shipping will run $50.00 just kidding. Let me know if you find anyone who sells them new. I never have.

06-28-2006, 06:27 AM	#5
mbgmike Registered User Join Date: Aug 2005 Location: Pasadena,Tx /Pto Pta DR Posts: 5,415	Re: Carb piecs, supplier source someone?? part sent monday



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.