|
|
|
11-06-2006, 01:09 PM
|
#1 |
|
Wrenchin & Sandin!!!
Join Date: Aug 2006
Location: Joliet, IL.
Posts: 523
|
Bench Seat Question
I've ripped apart my factory bench seat and ordered new foam. It has the zig zag springs at the bottom. Other than being broke which they are not, how do I tell if they are ok? When driving I sank down pretty far. Had to throw a pillow under me to sit right. Has anyone put a piece of plywood or something between the springs and foam to stiffen it up a bit? Or do you think new foam will take care of it? Any advice would be helpful. Thanks.....
__________________
Randy  Shorewood, IL. My Favorite eBay Searches My Driver Restore Thread 1971 C10 Longbed 2005 Silverado Shortbed 2005 FXDWG |
|
|
|
11-06-2006, 04:38 PM
|
#2 |
|
Wrenchin & Sandin!!!
Join Date: Aug 2006
Location: Joliet, IL.
Posts: 523
|
Re: Bench Seat Question
anyone???
__________________
Randy Shorewood, IL. My Favorite eBay Searches My Driver Restore Thread 1971 C10 Longbed 2005 Silverado Shortbed 2005 FXDWG |
|
|
|
|
11-06-2006, 04:59 PM
|
#3 |
|
It's a catastrophic success.
 
Join Date: Jan 2003
Location: Oklahoma
Posts: 2,077
|
Re: Bench Seat Question
This is probably one of those you will have to make an educated guess.Before and after the foam is removed compare the drivers side to the middle or pass side. I imagine they weaken over time and unless they are broken it wiill be hard to judge but if it was pretty squishy before and the pad was so-so then figure the the springs are shot on the drivers side
|
|
|
|
|
11-06-2006, 09:31 PM
|
#4 |
|
Senior Member
Join Date: Nov 2005
Location: northwestern wi
Posts: 2,111
|
Re: Bench Seat Question
if it leans it will still lean after a boundle of money if you don't repair the foundation{ springs} do it right and do it once
__________________
common sense isn't so common anymore |
|
|
|
|
11-06-2006, 09:46 PM
|
#5 | |
|
Wrenchin & Sandin!!!
Join Date: Aug 2006
Location: Joliet, IL.
Posts: 523
|
Re: Bench Seat Question
Quote:
Yea that's kinda what I was asking. Other then being broken what were other signs that the springs were bad? Loose? a couple are a little longer but not much. Guess I should just say hell with it and change them all.
__________________
Randy Shorewood, IL. My Favorite eBay Searches My Driver Restore Thread 1971 C10 Longbed 2005 Silverado Shortbed 2005 FXDWG |
|
|
|
|
|
12-02-2010, 05:15 PM
|
#6 | |
|
Registered User
Join Date: Mar 2004
Location: Colorado
Posts: 24
|
Re: Bench Seat Question
I'm also interested in parts or methods to diagnos and repair defective springs. I too have a sagging seat on drivers side. I proped up springs with a 1x4 piece of wood. Wish there was parts to rebuild the springs to remove the sagging issue.
I'm also interested in parts or methods to diagnos and repair defective springs. So another question could you remove the springs and replace that with the solid foam lower that I've seen at LMC truck?? Quote:
__________________
1971 Suburban 3/4 axles needs a lot of rust replaced |
|
|
|
|
 |
| Bookmarks |
|
|
Hybrid Mode
