Cab Bushing bolt snapped - The 1947 - Present Chevrolet & GMC Truck Message Board Network

chevymotocross · 10-29-2007, 01:05 PM

My passenger side lower cab bushing was shot, so I ordered a new bushing, bolt, and retainer. Luckily, there is a rot hole in my floor, directly above the bolt so I was able to spray penatrating oil on it every day this past week. Well it obviously didn't help any because the head of the bolt snapped right off! Now I am stuck and I can't get the rest of this weak bolt out. Any ideas?

**old Rusty C10** · 10-29-2007, 01:12 PM

how about applying heat from a propane torch on the nut then using a vise grip from underneath
you could also spray the penetrating oil from below
another option is to drill out the bolt from above hollowing out the center some ( as much as you can without damaging the threads of the nut
the last option is to cut out the floor support and replace it but that is kinda extreme

chevymotocross · 10-29-2007, 01:19 PM

Unfortunately, there is nothing to grab on to from the bottom, it snapped flush. The bolt is still there at the top, but since the bolt is surrounded by a small box, you can't even get a vise grip in there. I think my only solution is to drill out the bolt. If I damage the threads where the bolt goes through, I will just use the new bolt, nut, and washer.

chevymotocross · 10-29-2007, 02:13 PM

After my lunch I think I am actually going to thread on, and weld a nut. This way, I can hopefully take the bolt out from the top.

68K20 x Drill · 10-29-2007, 04:55 PM

If you drill it with a reverse rotation bit, it might yank out, but I've had good luck with nutwelding too.

**old Rusty C10** · 10-29-2007, 06:04 PM

Let us know how it goes hey if ya make this one easy ill bring ya my truck to do! KIDDING

10-29-2007, 01:05 PM	#1
chevymotocross Registered User Join Date: May 2007 Location: East Haven, CT Posts: 882	Cab Bushing bolt snapped My passenger side lower cab bushing was shot, so I ordered a new bushing, bolt, and retainer. Luckily, there is a rot hole in my floor, directly above the bolt so I was able to spray penatrating oil on it every day this past week. Well it obviously didn't help any because the head of the bolt snapped right off! Now I am stuck and I can't get the rest of this weak bolt out. Any ideas?

10-29-2007, 01:12 PM	#2
old Rusty C10 Robert Olson Transport Join Date: Oct 2002 Location: recent transplant to NC USA Posts: 20,310	Re: Cab Bushing bolt snapped how about applying heat from a propane torch on the nut then using a vise grip from underneath you could also spray the penetrating oil from below another option is to drill out the bolt from above hollowing out the center some ( as much as you can without damaging the threads of the nut the last option is to cut out the floor support and replace it but that is kinda extreme __________________ Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!!

10-29-2007, 01:19 PM	#3
chevymotocross Registered User Join Date: May 2007 Location: East Haven, CT Posts: 882	Re: Cab Bushing bolt snapped Unfortunately, there is nothing to grab on to from the bottom, it snapped flush. The bolt is still there at the top, but since the bolt is surrounded by a small box, you can't even get a vise grip in there. I think my only solution is to drill out the bolt. If I damage the threads where the bolt goes through, I will just use the new bolt, nut, and washer.

10-29-2007, 02:13 PM	#4
chevymotocross Registered User Join Date: May 2007 Location: East Haven, CT Posts: 882	Re: Cab Bushing bolt snapped After my lunch I think I am actually going to thread on, and weld a nut. This way, I can hopefully take the bolt out from the top.

10-29-2007, 04:55 PM	#5
68K20 x Drill Registered User Join Date: Apr 2007 Location: Freedom CA Posts: 488	Re: Cab Bushing bolt snapped If you drill it with a reverse rotation bit, it might yank out, but I've had good luck with nutwelding too. __________________ 68 Chevrolet k20 Longbed 350 SM465/205, Dana 44, 14bolt, Power steering, Power Disk Brakes, 35" BFGs. 84 Chevrolet Suburban K20 6.2 Banks turbo TH400/NP208 Now with G80 68 GMC C20 Parts? Truck And a few cars Last edited by 68K20 x Drill; 10-29-2007 at 04:55 PM.

10-29-2007, 06:04 PM	#6
old Rusty C10 Robert Olson Transport Join Date: Oct 2002 Location: recent transplant to NC USA Posts: 20,310	Re: Cab Bushing bolt snapped Let us know how it goes hey if ya make this one easy ill bring ya my truck to do! KIDDING __________________ Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.