hood hinge? can't get her aligned - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Greubin · 08-18-2008, 10:03 PM

I've adjusted the trailing bolt on the passenger hinge to try and pull the hood down flush, but still not there. If I push on the hood, it will almost sit flush, is the hinge shot or what??!! Any suggestions are greatly appreciated.

Number98 · 08-18-2008, 10:07 PM

This usually means that your springs are worn out.

dan42 · 08-18-2008, 10:08 PM

Mine does the same thing - some day I'll replace the hinges.

Longhorn Man · 08-18-2008, 10:12 PM

worn springs and/or hinges.
A band aid fix, loosen the 3 bolts that hold the hinge to the fender, now puth the hood up, as in opening it further than it is supposed to go. Not a lot of force, just enough to pivit the hinge. While holding in the 'further up' position, tighten the bolts back down. Very slowly lower the hood once the bolts are tight. Watch the rear edge of the hood, it may come in contact with the cowl panel. If it gets close, or actually touches, then loosen the hinge to hood bolts and pull it away.
This will snug the rear of the hood down once you get it ballanced out.

BLACK AND BLUE 67-72 · 08-18-2008, 10:36 PM

Just like Longhorn said^^^^^^

Greubin · 08-18-2008, 11:30 PM

Quote:

Originally Posted by Longhorn Man

worn springs and/or hinges.
A band aid fix, loosen the 3 bolts that hold the hinge to the fender, now puth the hood up, as in opening it further than it is supposed to go. Not a lot of force, just enough to pivit the hinge. While holding in the 'further up' position, tighten the bolts back down. Very slowly lower the hood once the bolts are tight. Watch the rear edge of the hood, it may come in contact with the cowl panel. If it gets close, or actually touches, then loosen the hinge to hood bolts and pull it away.
This will snug the rear of the hood down once you get it ballanced out.

Thanks Longhorn - I've already tried this. Looks like a new hinge is in my future - LMC truck here I come

Botietruck · 08-19-2008, 06:05 AM

Before you replace that hinge, spray all pivot points good with a spray lube such as white lithium grease. Work the hood up and down several times and spray it again. Try that before replacing the hinge.
If you have to buy a new hinge, get a genuine GM hinge & spring, they're still available!

JPSAUTO · 08-19-2008, 07:02 AM

Had the same problem with mine, new hinges solved the problem AND they are still available from the General pt#'s 3911705 left, 3911706 right

67ChevyRedneck · 08-19-2008, 11:15 AM

Quote:

Originally Posted by JPSAUTO

Had the same problem with mine, new hinges solved the problem AND they are still available from the General pt#'s 3911705 left, 3911706 right

Thanks for the PN's. I just ordered a set through GMpartsdirect.com

The LH hinge was $13 more than the RH one, I wonder if they're a little harder to find (not as many left)?

A little expensive, but I've needed new hinges for years. Maybe my hood will lay flat without my help now

kxmotox247 · 08-19-2008, 03:07 PM

Quote:

Originally Posted by JPSAUTO

Had the same problem with mine, new hinges solved the problem AND they are still available from the General pt#'s 3911705 left, 3911706 right

Are these #'s for the whole assembly or did you have to resuse your old springs?

lowdownstar · 08-19-2008, 09:49 PM

let us know how you make out with gm direct and if it helps with your hood trouble. I am having the same thing going on with my hood. Have you used Gm direct before? if so how are they? there prices didn't look all that bad.

thanks Ray

67ChevyRedneck · 08-20-2008, 07:51 AM

Quote:

Originally Posted by lowdownstar

let us know how you make out with gm direct and if it helps with your hood trouble. I am having the same thing going on with my hood. Have you used Gm direct before? if so how are they? there prices didn't look all that bad.

thanks Ray

This will be the first "classic" parts I've bought from them, but I've bought a few things for my silverado from them and shipping was fairly quick. They're prices are *usually* a good bit lower than a dealer, but then the slap ya with about $10 shipping for each item, but if you don't live in NC, no tax, so it could be a wash

I'll usually call our local dealer first with the PN's (they won't take orders over the phone, so I just call and ask for the prices) then compare to GMPD and they're usually a good bit cheaper. Normally, the dealer has to order stuff anyway, so you've got to wait anyway.

Greubin · 09-02-2008, 04:44 PM

Quote:

Originally Posted by JPSAUTO

Had the same problem with mine, new hinges solved the problem AND they are still available from the General pt#'s 3911705 left, 3911706 right

So is L/H and R/H as viewed from Drivers seat or from facing the front of the engine?

Thanks,

GREASEMONKEY72 · 08-19-2008, 10:14 PM

Quote:

Originally Posted by Greubin

I've adjusted the trailing bolt on the passenger hinge to try and pull the hood down flush, but still not there. If I push on the hood, it will almost sit flush, is the hinge shot or what??!! Any suggestions are greatly appreciated.

love the color

Greubin · 08-19-2008, 10:21 PM

Quote:

Originally Posted by GREASEMONKEY72

love the color

Thanks

GREASEMONKEY72 · 08-19-2008, 10:25 PM

Quote:

Originally Posted by Greubin

Thanks

youre welcome

Andy4639 · 08-20-2008, 01:33 PM

Just talked to the local dealer they can't pull a picture of them to see if the spring comes with it but the prices are $99.00 for LEFT and $78.00 RIGHT.
I'll buy the powder coated ones off E-bay for $99.00 before I pay that much.

LMC price in the summer book is $39.95 each. without springs.
Spring kit has both springs in it for $19.95.
So $60.00+ shipping from LMC.

67ChevyRedneck · 08-20-2008, 02:13 PM

Andy, that's why I used GMpartsdirect.com. I paid $131 SHIPPED and shipping was $22 of that. I've read too many horror stories on here about the aftermarket stuff. This should be a "one time" buy for me. Certain things I'll cheap out on, but good hood hinges aren't one of them. Hopefully I'll get another 40 years out of 'em.

PanelDeland · 08-20-2008, 07:06 PM

The aftermarket hood hinges I have seen seem inferior.I haven't used a set and would probably buy GM since I have heard bad about the aftermarket ones.

lowdownstar · 08-20-2008, 08:44 PM

Hey Redneck

Thanks for the feed back! I have to tell you i just sat here and read all ten pages of your build and man your a hard worker, and you did a really nice job on that truck! it looks sweet

Thanks again Ray

67ChevyRedneck · 08-27-2008, 10:03 PM

Quote:

Originally Posted by lowdownstar

Hey Redneck

Thanks for the feed back! I have to tell you i just sat here and read all ten pages of your build and man your a hard worker, and you did a really nice job on that truck! it looks sweet

Thanks again Ray

Thanks! I can't wait to tear it apart again

(seriously)

Got my hinges today... DEFINITELY NOS. Although I was hopeful, I had a feeling they were "hinges only," which they were... I couldn't find springs listed on GMpartsdirect.com.

Are the 73-87 springs exactly the same (I have no idea, just throwin' that out there.)

Soooo..... who sells GOOD hood springs?

lowdownstar · 08-28-2008, 06:33 AM

Your crazy!!!!! but i understand that is the funny part. there is something about these old cars and trucks they keep begging us to make them better.
give it hell my friend, take it apart and have some fun, that is what it's all about.

Ray

Andy4639 · 08-28-2008, 06:46 AM

Computer shopping again.

Says orignal GM hinges.

http://www.brotherstrucks.com/prodin...number=HNG7200

http://www.lategreatchevy.com/produc...dept%5Fid=1457

**leddzepp** · 09-03-2008, 01:11 PM

Quote:

Originally Posted by Andy4639

Computer shopping again.

Says orignal GM hinges.

http://www.brotherstrucks.com/prodin...number=HNG7200

http://www.lategreatchevy.com/produc...dept%5Fid=1457

If you buy these from Brothers, all they do is get them from another vendor (most likely GMpartsdirect), and then add their "finders fee" onto them. They do NOT have them in stock (they pretty much have NOTHING in stock anyways) I know because I live right down the street from them.

PanelDeland · 09-02-2008, 05:15 PM

All parts are listed as veiwed from the drivers seat.At least that's what I've been told.It's always worked for me.

08-18-2008, 10:03 PM	#1
Greubin Registered User Join Date: Dec 2005 Location: SJC Posts: 158	hood hinge? can't get her aligned I've adjusted the trailing bolt on the passenger hinge to try and pull the hood down flush, but still not there. If I push on the hood, it will almost sit flush, is the hinge shot or what??!! Any suggestions are greatly appreciated. Attached Images __________________ ___________ Greubin '71 C20 custom - GM Crate 350CI/290HP, BTO 700R4 level II, Qjet, and HEI

08-18-2008, 10:07 PM	#2
Number98 Prestige Worldwide Join Date: Feb 2001 Location: Worldwide Posts: 2,552	Re: hood hinge? can't get her aligned This usually means that your springs are worn out.

08-18-2008, 10:08 PM	#3
dan42 Registered User Join Date: Feb 2007 Location: Cali Central Coast Posts: 5,191	Re: hood hinge? can't get her aligned Mine does the same thing - some day I'll replace the hinges. __________________ '67 SWB Fleetside ZZ4/350/Tremec 5-speed/4link/Scott's IFS - and fun as heck! SOLD Click here to support the board Philippians 4: 6-7

08-18-2008, 10:12 PM	#4
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	Re: hood hinge? can't get her aligned worn springs and/or hinges. A band aid fix, loosen the 3 bolts that hold the hinge to the fender, now puth the hood up, as in opening it further than it is supposed to go. Not a lot of force, just enough to pivit the hinge. While holding in the 'further up' position, tighten the bolts back down. Very slowly lower the hood once the bolts are tight. Watch the rear edge of the hood, it may come in contact with the cowl panel. If it gets close, or actually touches, then loosen the hinge to hood bolts and pull it away. This will snug the rear of the hood down once you get it ballanced out.

08-18-2008, 10:36 PM	#5
BLACK AND BLUE 67-72 Firefighter Join Date: Feb 2001 Location: Yellville, Ar, USA Posts: 1,943	Re: hood hinge? can't get her aligned Just like Longhorn said^^^^^^ __________________ '72 Chevy SWB 350 Auto '67 GMC LWB 350 4 speed '70 Chevy 4x4 Stepside 350 Auto Yellville, Ar. USA

08-19-2008, 06:05 AM	#7
Botietruck '71 chevy s.bed/s.side Join Date: Mar 2005 Location: Chesapeake, VA Posts: 1,571	Re: hood hinge? can't get her aligned Before you replace that hinge, spray all pivot points good with a spray lube such as white lithium grease. Work the hood up and down several times and spray it again. Try that before replacing the hinge. If you have to buy a new hinge, get a genuine GM hinge & spring, they're still available! __________________ STILL PLAYS WITH CARS...AND TRUCKS!! Parents! Be good to your kids...they get to choose your nursing home! 250 I-6 with a 3 speed Saginaw and Borg Warner Overdrive...She's got overdrive! Last edited by Botietruck; 08-19-2008 at 06:06 AM.

08-19-2008, 07:02 AM	#8
JPSAUTO Registered User Join Date: Feb 2004 Location: Indiana Posts: 158	Re: hood hinge? can't get her aligned Had the same problem with mine, new hinges solved the problem AND they are still available from the General pt#'s 3911705 left, 3911706 right

08-19-2008, 09:49 PM	#11
lowdownstar big guy Join Date: Jun 2008 Location: mass Posts: 824	Re: hood hinge? can't get her aligned let us know how you make out with gm direct and if it helps with your hood trouble. I am having the same thing going on with my hood. Have you used Gm direct before? if so how are they? there prices didn't look all that bad. thanks Ray

08-20-2008, 01:33 PM	#17
Andy4639 Old member Join Date: Jan 2002 Location: Liberty, & Garden City S.C. , U.S. Posts: 19,945	Re: hood hinge? can't get her aligned Just talked to the local dealer they can't pull a picture of them to see if the spring comes with it but the prices are $99.00 for LEFT and $78.00 RIGHT. I'll buy the powder coated ones off E-bay for $99.00 before I pay that much. LMC price in the summer book is $39.95 each. without springs. Spring kit has both springs in it for $19.95. So $60.00+ shipping from LMC. __________________ 1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs.

08-20-2008, 02:13 PM	#18
67ChevyRedneck Hittin E-Z Street on Mud Tires Join Date: Nov 2004 Location: Greenville, SC Posts: 23,090	Re: hood hinge? can't get her aligned Andy, that's why I used GMpartsdirect.com. I paid $131 SHIPPED and shipping was $22 of that. I've read too many horror stories on here about the aftermarket stuff. This should be a "one time" buy for me. Certain things I'll cheap out on, but good hood hinges aren't one of them. Hopefully I'll get another 40 years out of 'em. __________________ Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride American Born, Country by the Grace of God 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications! Last edited by 67ChevyRedneck; 08-20-2008 at 02:15 PM.

08-20-2008, 07:06 PM	#19
PanelDeland I am a Referee of life. Join Date: Jun 2000 Location: Greensboro N.C. Posts: 13,992	Re: hood hinge? can't get her aligned The aftermarket hood hinges I have seen seem inferior.I haven't used a set and would probably buy GM since I have heard bad about the aftermarket ones. __________________ The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion. You can't fix stupid,not even with duct tape. "My appearance is due to the fact that "GOD" does punish you for having too much fun!" Barrett-Jackson has perfected alchemy,they make rust into gold! "You can lead a horse to water but you can't saddle a duck" "Cleverly disguised as a 'Responsible Adult' "Sometimes your Knight in shining armor is just a retard in tinfoil"

08-20-2008, 08:44 PM	#20
lowdownstar big guy Join Date: Jun 2008 Location: mass Posts: 824	Re: hood hinge? can't get her aligned Hey Redneck Thanks for the feed back! I have to tell you i just sat here and read all ten pages of your build and man your a hard worker, and you did a really nice job on that truck! it looks sweet Thanks again Ray

08-28-2008, 06:33 AM	#22
lowdownstar big guy Join Date: Jun 2008 Location: mass Posts: 824	Re: hood hinge? can't get her aligned Your crazy!!!!! but i understand that is the funny part. there is something about these old cars and trucks they keep begging us to make them better. give it hell my friend, take it apart and have some fun, that is what it's all about. Ray

08-28-2008, 06:46 AM	#23
Andy4639 Old member Join Date: Jan 2002 Location: Liberty, & Garden City S.C. , U.S. Posts: 19,945	Re: hood hinge? can't get her aligned Computer shopping again. Says orignal GM hinges. http://www.brotherstrucks.com/prodin...number=HNG7200 http://www.lategreatchevy.com/produc...dept%5Fid=1457 __________________ 1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs.

09-02-2008, 05:15 PM	#25
PanelDeland I am a Referee of life. Join Date: Jun 2000 Location: Greensboro N.C. Posts: 13,992	Re: hood hinge? can't get her aligned All parts are listed as veiwed from the drivers seat.At least that's what I've been told.It's always worked for me. __________________ The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion. You can't fix stupid,not even with duct tape. "My appearance is due to the fact that "GOD" does punish you for having too much fun!" Barrett-Jackson has perfected alchemy,they make rust into gold! "You can lead a horse to water but you can't saddle a duck" "Cleverly disguised as a 'Responsible Adult' "Sometimes your Knight in shining armor is just a retard in tinfoil"



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.