The Great Critter Revival ‘09 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Critter · 02-24-2009, 10:56 PM

Well, I figure it is time for me to put this in some sort of build thread, even though at the moment it is made up more of destruction than building.

A little history…I had been looking for a 1st gen Blazer off and on starting around 2001. I got serious a couple years ago and picked this one up in August of 2006. I knew it had some issues but I also knew it had a lot of the options I wanted. I.E. tilt, A/C, 350/TH350, etc. After I bought it I realized it was a Highlander package as well. For the last couple of years I have been gathering parts, casually fixing things, and getting it road worthy. Tuned up the engine, rebuilt the tranny, rebuilt the front axle/spring bushings, new rear suspension. Blah, Blah, Blah. This winter it finally became fully street legal…just in time for me to get serious about restoring it. I have most of the big parts gathered up like a full set of virtually spotless OEM sheet metal to bolt on (except for a driver door that I am currently looking for), along with a new rear axle and some newer style GM seats from a 2001 truck. The rest of the parts like, grill parts, pretty much all of the interior pieces, and all the seals/gaskets and so on will be purchased as I go.

The first pic is where she was sitting back in 2006. The others were taken after I had done some work.

Critter · 02-24-2009, 11:02 PM

As far as my goals for this thing, I plan on taking the resto-mod approach. I want the body to look basically stock as far as trim, bumpers, and a solid color paint scheme (still haven’t figured out which color that will be), the interior will be stockish with modern updates here and there. Under the hood things such as wiring and plumbing will be cleaned up and improved as needed and the original 350 will be rebuilt and mildly upgraded. I would like for it to eventually be nice enough for me to take to local car shows and club gatherings, along with weekend drives to the river, beach, etc. I don’t plan to run it up and down the rocks or anything but at the same time I’m going to drive it where I want and ENJOY it.

I also think I need to add that I have owned and worked on a number of old Chevy trucks, but this is my first attempt at a “frame off” rebuild, so I’m sure it will be slow and painful for everyone.

Critter · 02-24-2009, 11:09 PM

I started pulling the front clip off a few weeks ago and then the doors. This week I got going on the rockers. Here are a few pics of you typical rust. I had a fairly decent idea of how bad it was being that I could see most of it through the holes. Time to order some patch panels…site venders here I come. I plan to totally fix the drivers side before I move to the passenger. Plus I got a couple little spots to fix on the firewall, but they are on flat surfaces and should be fairly easy to patch.

Critter · 02-24-2009, 11:16 PM

Finally got the drivers rocker off. YEAH! As I figured, I will need inner and outer rockers, the outer floor strip, kick panel, front cab corner, and lower front bedside area.

Critter · 02-24-2009, 11:18 PM

...and a couple more for the heck of it.

Critter · 02-24-2009, 11:21 PM

here they are

vtblazer · 02-25-2009, 08:25 AM

Quote:

Originally Posted by Critter

Finally got the drivers rocker off. YEAH! As I figured, I will need inner and outer rockers, the outer floor strip, kick panel, front cab corner, and lower front bedside area.

For your inner rocker replacement, look into the part Tri-Pro sells for trucks, you get alot more to work with than the blazer version.
The full length truck part includes the lower 'A' pillar holes and a fair amount of floor area too, it'll give you more option's to work with.

Pic of the part I'm talking about:

Here's a decent thread to look over, it addresses where your heading...

http://67-72chevytrucks.com/vboard/s...d.php?t=249323

Enjoy...

**lks dcvn** · 02-25-2009, 09:30 AM

Watching this one...I will have a comparable fix on a 72 4x4 Blazer when it shows up in a few weeks from Columbus, Ohio after a trade for my 72 C/20...

Good Luck with your build - as overwhelming as it will be - the end result will justify the stress of doing it...

Jtrux · 02-25-2009, 01:13 PM

Quote:

Originally Posted by vtblazer

For your inner rocker replacement, look into the part Tri-Pro sells for trucks, you get alot more to work with than the blazer version.
The full length truck part includes the lower 'A' pillar holes and a fair amount of floor area too, it'll give you more option's to work with.

Pic of the part I'm talking about:

Here's a decent thread to look over, it addresses where your heading...

http://67-72chevytrucks.com/vboard/s...d.php?t=249323

Enjoy...

Nice link, lots of good pics.

Mint68 · 02-24-2009, 11:02 PM

Gotta love Texas. In Nebraska it is extremely difficult to find something in that good of shape. Everything has been rotting forever here. Good find, I really like the wheels.

OldCreek · 02-25-2009, 03:21 AM

What's it called when you use your own name in the title for your build thread?

Jtrux · 02-25-2009, 04:13 AM

Quote:

Originally Posted by OldCreek

What's it called when you use your own name in the title for your build thread?

Technically speaking, Critter is the name of his blazer, he's a wierdo.

litebulblsc · 02-25-2009, 08:21 AM

If you don't mind me going off topic and asking, what is the highlander option?

**Yukon Jack** · 02-25-2009, 06:30 PM

Will be a fun project to watch - sounds like you have a good plan. The color looks alot like the color on my K5.

RckyMntnKng · 02-26-2009, 03:21 PM

Cool rig!

I love those wheels....anyone know where you could get them in 8 on 6.5?

mudman316 · 02-26-2009, 04:51 PM

I too will be watching closely as I will be doing the same to mine this spring and summer. I will have to replace bottom boxes also. nice project truck keep at it you'll get it done. at least that is what i will be telling myself during mine to try to keep a little sanity.

Are you supporting the pillars with anything while you do the work or is the boxes doing their job still?

Critter · 02-26-2009, 06:33 PM

Quote:

Originally Posted by Mint68

Gotta love Texas. In Nebraska it is extremely difficult to find something in that good of shape. Everything has been rotting forever here. Good find, I really like the wheels.

Texas is weird, East Texas trucks = RUST, but West Texas = SoCal/Arizona sheet metal. Here in Central Tex, it's 50/50. I guess mines about average condition for the area.

Quote:

Originally Posted by litebulblsc

If you don't mind me going off topic and asking, what is the highlander option?

Basically it is a trim package, there were "A" "B" & "C" Highlander options. Usually they consist of A/C, ps, automatic, tinted windows, chrome, etc. The main difference is they had a special plaid seat covers. They weren't OVERLY rare or anything, just kinda a nice bonus for me to find after I bought the thing. If the search function was working, you could find info on it pretty easy.

Quote:

Originally Posted by vtblazer

For your inner rocker replacement, look into the part Tri-Pro sells for trucks, you get alot more to work with than the blazer version.
The full length truck part includes the lower 'A' pillar holes and a fair amount of floor area too, it'll give you more option's to work with.

Pic of the part I'm talking about:

Here's a decent thread to look over, it addresses where your heading...

http://67-72chevytrucks.com/vboard/s...d.php?t=249323

Enjoy...

THANK YOU! I am going to go this route...gonna make a parts order next week.

Quote:

Originally Posted by RckyMntnKng

Cool rig!

I love those wheels....anyone know where you could get them in 8 on 6.5?

They are out there if you look, not sure if you can still buy them new or not; mine were put on back in the 70's according to the PO. They annoy me cause they are made from magnesium and need those special lugnuts, but they have kinda grown on me because of the "nostalgia" I guess.

Quote:

Originally Posted by mudman316

Are you supporting the pillars with anything while you do the work or is the boxes doing their job still?

I don't THINK I need to do that, I have some floor jacks to put under things if I need to, but my torsion boxes appear to be in great shape (no rot what-so-ever, just surface rust), somehow, so I feel that everything will stay in place. Somebody tell me if I have lost my mind.

1956cameo · 02-26-2009, 10:15 PM

This should be an interesting build to watch. I cant wait to see more.

vtblazer · 02-27-2009, 07:20 AM

Quote:

Originally Posted by Critter

I don't THINK I need to do that, I have some floor jacks to put under things if I need to, but my torsion boxes appear to be in great shape (no rot what-so-ever, just surface rust), somehow, so I feel that everything will stay in place. Somebody tell me if I have lost my mind.

At a minimum, do something to maintain the door opening.

Your going to be getting into the front pillar and once you break it loose, you'll be amazed at how much the firewall is going to move.

Fair warning though, build the brace so it's 'convenient' to work around.

72Levi · 03-02-2009, 12:41 AM

Keep at it, you can take care of that. I admire the heck out of you for bringing back your K5. I've always liked the dark green Blazers.

**jaros44sr** · 03-02-2009, 10:45 AM

Shame it's that bad in the cowl area, but it's to be expected as all the crap falls into it. I would take more metal out back to the seams, then you can really get a handle on it. If you leave the forward edge, where the curve starts, you should be able to fix it with a flat sheet of metal. When mine go bad, I want to put in a piece of stainless and screw it in so I can check it from time to time. Also this will allow you to put a sealer between the seam and metal

Whats the inside area look like(kick panel)

Critter · 03-06-2009, 02:01 AM

Quote:

Originally Posted by jaros44sr

I would take more metal out back to the seams, then you can really get a handle on it. If you leave the forward edge, where the curve starts, you should be able to fix it with a flat sheet of metal.

Whats the inside area look like (kick panel)

That's what I plan to do this weekend. I was a little scared to it, but then I read this.

http://67-72chevytrucks.com/vboard/s...ad.php?t=72472

It gave me the false sense of confidence I need to start cutting

....pics to follow.

Oh, and my kick panel has some rot along the bottom 1 inch where it meets the floor board, no better or worse than most of the others you see around here.

**jaros44sr** · 03-06-2009, 07:00 AM

Have fun this weekend and take lots of pics for us to look at, I'm a junkie for people's progress

Critter · 03-07-2009, 05:19 PM

Day 12…
ordered drivers side patch panels from Tri-Pro yesterday…
found more rust around the firewall today…I’m scared…
starting to freak out…

BLUE THUNDER · 03-08-2009, 11:33 AM

Dude, your knee deep in it now. A little more work and the Critter will be on the road in no time. Gimme a shout if you need a hand. Way to go so far though. Later.

02-24-2009, 10:56 PM	#1
Critter Future TOTM Winner Join Date: Aug 2006 Location: Bulverde, TX Posts: 2,692	The Great Critter Revival ‘09 Well, I figure it is time for me to put this in some sort of build thread, even though at the moment it is made up more of destruction than building. A little history…I had been looking for a 1st gen Blazer off and on starting around 2001. I got serious a couple years ago and picked this one up in August of 2006. I knew it had some issues but I also knew it had a lot of the options I wanted. I.E. tilt, A/C, 350/TH350, etc. After I bought it I realized it was a Highlander package as well. For the last couple of years I have been gathering parts, casually fixing things, and getting it road worthy. Tuned up the engine, rebuilt the tranny, rebuilt the front axle/spring bushings, new rear suspension. Blah, Blah, Blah. This winter it finally became fully street legal…just in time for me to get serious about restoring it. I have most of the big parts gathered up like a full set of virtually spotless OEM sheet metal to bolt on (except for a driver door that I am currently looking for), along with a new rear axle and some newer style GM seats from a 2001 truck. The rest of the parts like, grill parts, pretty much all of the interior pieces, and all the seals/gaskets and so on will be purchased as I go. The first pic is where she was sitting back in 2006. The others were taken after I had done some work. Attached Images __________________ 72 Chevy CST K5 HIGHLANDER BLAZER Getting a 6.0,NV4500,NP205,14BFF (Currently laying all over the place in little pieces) 72 Chevy swb step-side "LS" 6.0 Here's a build thread of sorts 2002 HD2500 Crew Cab, 8.1L Allison 4x4 Daily Driver Check it out www.lsdyno.com Last edited by Critter; 02-25-2009 at 12:36 AM.

02-24-2009, 11:02 PM	#2
Critter Future TOTM Winner Join Date: Aug 2006 Location: Bulverde, TX Posts: 2,692	Re: The Great Critter Revival ‘09 As far as my goals for this thing, I plan on taking the resto-mod approach. I want the body to look basically stock as far as trim, bumpers, and a solid color paint scheme (still haven’t figured out which color that will be), the interior will be stockish with modern updates here and there. Under the hood things such as wiring and plumbing will be cleaned up and improved as needed and the original 350 will be rebuilt and mildly upgraded. I would like for it to eventually be nice enough for me to take to local car shows and club gatherings, along with weekend drives to the river, beach, etc. I don’t plan to run it up and down the rocks or anything but at the same time I’m going to drive it where I want and ENJOY it. I also think I need to add that I have owned and worked on a number of old Chevy trucks, but this is my first attempt at a “frame off” rebuild, so I’m sure it will be slow and painful for everyone. Attached Images __________________ 72 Chevy CST K5 HIGHLANDER BLAZER Getting a 6.0,NV4500,NP205,14BFF (Currently laying all over the place in little pieces) 72 Chevy swb step-side "LS" 6.0 Here's a build thread of sorts 2002 HD2500 Crew Cab, 8.1L Allison 4x4 Daily Driver Check it out www.lsdyno.com

02-24-2009, 11:09 PM	#3
Critter Future TOTM Winner Join Date: Aug 2006 Location: Bulverde, TX Posts: 2,692	Re: The Great Critter Revival ‘09 I started pulling the front clip off a few weeks ago and then the doors. This week I got going on the rockers. Here are a few pics of you typical rust. I had a fairly decent idea of how bad it was being that I could see most of it through the holes. Time to order some patch panels…site venders here I come. I plan to totally fix the drivers side before I move to the passenger. Plus I got a couple little spots to fix on the firewall, but they are on flat surfaces and should be fairly easy to patch. Attached Images __________________ 72 Chevy CST K5 HIGHLANDER BLAZER Getting a 6.0,NV4500,NP205,14BFF (Currently laying all over the place in little pieces) 72 Chevy swb step-side "LS" 6.0 Here's a build thread of sorts 2002 HD2500 Crew Cab, 8.1L Allison 4x4 Daily Driver Check it out www.lsdyno.com Last edited by Critter; 02-25-2009 at 04:50 PM.

02-24-2009, 11:16 PM	#4
Critter Future TOTM Winner Join Date: Aug 2006 Location: Bulverde, TX Posts: 2,692	Re: The Great Critter Revival ‘09 Finally got the drivers rocker off. YEAH! As I figured, I will need inner and outer rockers, the outer floor strip, kick panel, front cab corner, and lower front bedside area. Attached Images __________________ 72 Chevy CST K5 HIGHLANDER BLAZER Getting a 6.0,NV4500,NP205,14BFF (Currently laying all over the place in little pieces) 72 Chevy swb step-side "LS" 6.0 Here's a build thread of sorts 2002 HD2500 Crew Cab, 8.1L Allison 4x4 Daily Driver Check it out www.lsdyno.com

02-24-2009, 11:18 PM	#5
Critter Future TOTM Winner Join Date: Aug 2006 Location: Bulverde, TX Posts: 2,692	Re: The Great Critter Revival ‘09 ...and a couple more for the heck of it. __________________ 72 Chevy CST K5 HIGHLANDER BLAZER Getting a 6.0,NV4500,NP205,14BFF (Currently laying all over the place in little pieces) 72 Chevy swb step-side "LS" 6.0 Here's a build thread of sorts 2002 HD2500 Crew Cab, 8.1L Allison 4x4 Daily Driver Check it out www.lsdyno.com

02-24-2009, 11:21 PM	#6
Critter Future TOTM Winner Join Date: Aug 2006 Location: Bulverde, TX Posts: 2,692	Re: The Great Critter Revival ‘09 here they are Attached Images __________________ 72 Chevy CST K5 HIGHLANDER BLAZER Getting a 6.0,NV4500,NP205,14BFF (Currently laying all over the place in little pieces) 72 Chevy swb step-side "LS" 6.0 Here's a build thread of sorts 2002 HD2500 Crew Cab, 8.1L Allison 4x4 Daily Driver Check it out www.lsdyno.com

02-25-2009, 09:30 AM	#8
lks dcvn Registered User Join Date: Jan 2007 Location: Columbus, Ohio Posts: 4,348	Re: The Great Critter Revival ‘09 Watching this one...I will have a comparable fix on a 72 4x4 Blazer when it shows up in a few weeks from Columbus, Ohio after a trade for my 72 C/20... Good Luck with your build - as overwhelming as it will be - the end result will justify the stress of doing it... Attached Images

02-24-2009, 11:02 PM	#10
Mint68 Registered User Join Date: Nov 2004 Location: Nebraska Posts: 762	Re: The Great Critter Revival ‘09 Gotta love Texas. In Nebraska it is extremely difficult to find something in that good of shape. Everything has been rotting forever here. Good find, I really like the wheels.

02-25-2009, 03:21 AM	#11
OldCreek Registered User Join Date: Jan 2007 Location: Central Coast California Posts: 1,026	Re: The Great Critter Revival ‘09 What's it called when you use your own name in the title for your build thread? __________________ 1972 K20 Suburban 5.7/700r4/NP205 Dana 44/H052 Sold 1972 C10 5.3L/4L60E 12bolt 5Lug - Sold 1971 K5 Blazer 6.0L LQ9 4L60E NP205 Dana 44/H052!!! 1970 K3500 1ton CrewCab 8.1L/Allison1000/NP205 Dana 60/14B!!!! - Sold 1984 K10 SWB 7.4L/4L80e/NP208 Corp 10/12 bolt Sold 1988 V30 CCLB 7.4L/TH400/NP205/Dana 60/Dana 70/3.73!!! (Sold) 2003 K2500HD 8.1/Allison1000/NP263

02-25-2009, 08:21 AM	#13
litebulblsc Registered User Join Date: Aug 2006 Location: LaSalle Mi Posts: 525	Re: The Great Critter Revival ‘09 If you don't mind me going off topic and asking, what is the highlander option?

02-25-2009, 06:30 PM	#14
Yukon Jack Post Whore Join Date: Feb 2000 Location: Rose Hill, KS, USA Posts: 12,686	Re: The Great Critter Revival ‘09 Will be a fun project to watch - sounds like you have a good plan. The color looks alot like the color on my K5. __________________ 1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14

02-26-2009, 03:21 PM	#15
RckyMntnKng Registered User Join Date: Apr 2007 Location: Meridian, Idaho Posts: 316	Re: The Great Critter Revival ‘09 Cool rig! I love those wheels....anyone know where you could get them in 8 on 6.5? __________________ 71 Jimmy: D60/14BFF, 9"F/11"B Lift, 350-350-203-205, Crossover Hydro steering, Beadlocks, Tube stuff and the bottomless cooler

02-26-2009, 04:51 PM	#16
mudman316 Registered User Join Date: Jan 2009 Location: chattanooga, tn. Posts: 104	Re: The Great Critter Revival ‘09 I too will be watching closely as I will be doing the same to mine this spring and summer. I will have to replace bottom boxes also. nice project truck keep at it you'll get it done. at least that is what i will be telling myself during mine to try to keep a little sanity. Are you supporting the pillars with anything while you do the work or is the boxes doing their job still? __________________ BE NICE IT PAYS IN THE END.

02-26-2009, 10:15 PM	#18
1956cameo Registered User Join Date: Apr 2008 Location: Angleton, TX Posts: 2,219	Re: The Great Critter Revival ‘09 This should be an interesting build to watch. I cant wait to see more.

03-02-2009, 12:41 AM	#20
72Levi Active Member Join Date: Feb 2006 Location: sa tx Posts: 851	Re: The Great Critter Revival ‘09 Keep at it, you can take care of that. I admire the heck out of you for bringing back your K5. I've always liked the dark green Blazers. __________________ 1972 K5 Blazer ALL ORIGINAL paint & engine, A/C, Tilt, 4sp, AM/FM, Tow Hooks, Aux Battery Tray, Tach, Vacuum 2004 FORD FX4 SuperCrew 2005 CTS-V 12 sec family car 2008 Buick Enclave AWD, Nav, & DVD, Wife LOVES it!



Register or Log In To remove these advertisements.

03-02-2009, 10:45 AM	#21
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,762	Re: The Great Critter Revival ‘09 Shame it's that bad in the cowl area, but it's to be expected as all the crap falls into it. I would take more metal out back to the seams, then you can really get a handle on it. If you leave the forward edge, where the curve starts, you should be able to fix it with a flat sheet of metal. When mine go bad, I want to put in a piece of stainless and screw it in so I can check it from time to time. Also this will allow you to put a sealer between the seam and metal Whats the inside area look like(kick panel) __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim Last edited by jaros44sr; 03-02-2009 at 10:50 AM.

03-06-2009, 07:00 AM	#23
jaros44sr Senior Member Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,762	Re: The Great Critter Revival ‘09 Have fun this weekend and take lots of pics for us to look at, I'm a junkie for people's progress __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

03-07-2009, 05:19 PM	#24
Critter Future TOTM Winner Join Date: Aug 2006 Location: Bulverde, TX Posts: 2,692	Re: The Great Critter Revival ‘09 Day 12… ordered drivers side patch panels from Tri-Pro yesterday… found more rust around the firewall today…I’m scared… starting to freak out… Attached Images __________________ 72 Chevy CST K5 HIGHLANDER BLAZER Getting a 6.0,NV4500,NP205,14BFF (Currently laying all over the place in little pieces) 72 Chevy swb step-side "LS" 6.0 Here's a build thread of sorts 2002 HD2500 Crew Cab, 8.1L Allison 4x4 Daily Driver Check it out www.lsdyno.com

03-08-2009, 11:33 AM	#25
BLUE THUNDER Registered User Join Date: May 2007 Location: San Antonio Posts: 993	Re: The Great Critter Revival ‘09 Dude, your knee deep in it now. A little more work and the Critter will be on the road in no time. Gimme a shout if you need a hand. Way to go so far though. Later.

Register or Log In To remove these advertisements.