Front axle question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

B.A. Blazer · 02-27-2009, 07:20 PM

Guys, my '72 Blazer has a broken passenger side axle shaft. What I need to know is whats interchangeable with it, do pickups have the same length shaft? What about newer year trucks?

Also, I know the 10 Bolt and Dana 44 are somewhat similar, will a shaft from that work or does it have to be from a 44? I'm dying to get this truck going again.

CPNEJR · 02-27-2009, 07:24 PM

the axles are interchangeable on open knuckle 44's between pickups and blazers. i believe that the only difference in 10 bolt axles is that the outer stub is a different length but i'm not sure on that one

B.A. Blazer · 02-27-2009, 09:59 PM

Quote:

Originally Posted by CPNEJR

the axles are interchangeable on open knuckle 44's between pickups and blazers. i believe that the only difference in 10 bolt axles is that the outer stub is a different length but i'm not sure on that one

On the 44's are they the same up until they changed to the 10 bolts in the mid 80's?

Critter · 02-27-2009, 10:09 PM

Quote:

Originally Posted by B.A. Blazer

On the 44's are they the same up until they changed to the 10 bolts in the mid 80's?

Like CPNEJR said, all of the open nuckle chevy D44 should work, but I believe they switched to the 10 bolt in 76 or so, not 80's.

Mike C · 02-28-2009, 10:49 AM

The outers are the same. It is the inner that is different on a 10 bolt. The 72 and earlyier trucks use a smaller u-joint than the later. Get yourself a 73-79 Dana 44 front.

02-27-2009, 07:20 PM	#1
B.A. Blazer Registered User Join Date: Jun 2008 Location: Bridgewater, MA Posts: 6	Front axle question Guys, my '72 Blazer has a broken passenger side axle shaft. What I need to know is whats interchangeable with it, do pickups have the same length shaft? What about newer year trucks? Also, I know the 10 Bolt and Dana 44 are somewhat similar, will a shaft from that work or does it have to be from a 44? I'm dying to get this truck going again.

02-27-2009, 07:24 PM	#2
CPNEJR Registered User Join Date: Sep 2003 Location: Franconia,N.H. Posts: 1,029	Re: Front axle question the axles are interchangeable on open knuckle 44's between pickups and blazers. i believe that the only difference in 10 bolt axles is that the outer stub is a different length but i'm not sure on that one __________________ (Only) Member of the CPNE Fan Club Aint that the truth 67 C-10 350 with 3-speed tranny and 308 gears swb step 82 Z28 Camaro 355 small block over 350 hp and a borg warner super t-10 (blown engine) 72 Chevy K20 Suburban (future project) 70 Chevy K20 now 68 GMC K2500 2003 Chevy 2500hd ccsb 4X4 (daily driver)

02-28-2009, 10:49 AM	#5
Mike C Registered User Join Date: Dec 1999 Location: Austin, TX, USA Posts: 7,727	Re: Front axle question The outers are the same. It is the inner that is different on a 10 bolt. The 72 and earlyier trucks use a smaller u-joint than the later. Get yourself a 73-79 Dana 44 front. __________________ 44 Willys MB 52 M38A1 64 Corvette Coupe 68 Camaro 'vert LT1 & TH700 69 Z/28 355 12.6's @110 69 Chevy Short Step 4 1/2"/7" drop 72 Jimmy 4WD 4spd 4" & 35's 02 GMC 2500HD 4x4 Duramax



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.