700r4 lockup wiring - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**americanmusc1e** · 03-19-2009, 11:17 AM

I'm installing a 700r4 in place of my old th350,
for the lockup wiring can i run a toggle switch and a brake switch and forget the pressure switch and vacuum switch??? I have an '87 trans out of a camaro and it has a square looking plug with three pins in it, which is power, which is ground and what is the other one for?????
thanks in advance

texanidiot25 · 03-19-2009, 12:11 PM

You have to have the TV cable, no matter what.

Indyuke · 03-19-2009, 12:55 PM

Yes, you can run a toggle along with the brake switch instead of a pressure switch. But why? It's much easier to wire up a pressure switch, plus it's much nicer to drive that way. Don't have to think about it.

And you don't absolutely need a vac switch. I put one in mine, but bypassed it the first day.

**americanmusc1e** · 03-19-2009, 01:47 PM

anybody know witch one is the "A" pin and witch one is the "D" pin?????

**americanmusc1e** · 03-19-2009, 02:12 PM

which pin do i run the 12 volts to???? and which do i ground???? and what is the third one for????

71meangreenc10 · 03-19-2009, 03:38 PM

Ill look it up this evening if no one els jumps in.

Smitty

**michael bustamante** · 03-19-2009, 05:17 PM

the plug should be labled which is which on the underside

cparman · 03-19-2009, 05:26 PM

the plug will be labeled. If I remember correctly, it will be the terminal in the upper left in your picture. I have a brake light switch, and a toggle, I did it this way so when I am poking along, and the engine is turning too few rpm, I can unlock the converter and eliminate the chuggle in the engine.

Andy4639 · 03-20-2009, 08:13 AM

I have mine just hooked up with a toggle on the dash. I bought the vacuum switch but just did away with it. It want lock up under 45MPH no way with the B&M kit. I assume you have the internal wiring done already to the transmission for this. I had it done while they built the transmission.

**americanmusc1e** · 03-20-2009, 03:39 PM

Quote:

Originally Posted by Andy4639

I have mine just hooked up with a toggle on the dash. I bought the vacuum switch but just did away with it. It want lock up under 45MPH no way with the B&M kit. I assume you have the internal wiring done already to the transmission for this. I had it done while they built the transmission.

thats how i'm going to do mine except i'm adding a brake switch too

Andy4639 · 03-20-2009, 08:00 PM

Why do you want a brake switch. Mine works fine even without it.

**americanmusc1e** · 03-20-2009, 10:05 PM

Quote:

Originally Posted by Andy4639

Why do you want a brake switch. Mine works fine even without it.

in case i forget to flip the switch when i have to slam on my brakes

Indyuke · 03-20-2009, 08:12 PM

Americanmuscle, GENERALLY, power goes to your (A) pin, top left on your pic. Ground is bottom left on your pic, I believe it's (D). And (B) is top right, part of the tranny overheat circuit. The reason I say generally is because GM had like 37 different ways they wired up the TCC. So double check.

If you want to control the TCC with a toggle switch, run power to (A) through a toggle switch, and put a jumper between the other two contacts.

The torque converter will lockup only when the tranny is in fourth AND you have the toggle flipped on.

Wire it up like this without the toggle and the converter will lock up every time it shifts to fourth gear. Hope this helps.

Indyuke · 03-21-2009, 12:21 AM

I think what andy means is, if it's wired to only lock up in fourth, as soon as you slam on your brakes, the transmission downshifts and the torque converter unlocks. Then when you get going again it upshifts and locks up again. Don't need a brake switch.

Andy4639 · 03-21-2009, 05:03 AM

Correct if the truck is ever out of fourth gear it want ,Shouldn't lockup at all. I can even back up with the switch on.

**LEEVON** · 03-21-2009, 09:45 AM

If you don't want to mess with a switch, it's only slightly more difficult to put in a vacuum switch and brake cancel switch. I found them to be plentiful at the junkyard and free, I believe I pulled my vacuum switch from a K5, along with a tiny blue vacuum booster. 12v from pin A to the brake cancel switch, then to the vacuum switch and you're all set.

**americanmusc1e** · 03-21-2009, 09:58 AM

thanks guys

68_c10_on20s · 08-04-2009, 08:30 PM

Im kinda in the same boat and need some advice.I am going just the opposite route and need help wiring up the 700.My truck is a 93 model and it had a v6 with a 4l60e tranny I had a 350/700 ive installed and need to wire up the lockup now.The 700 only has 3 wires going to it and the e trans had 12. I still have the cpu hooked up only becouse im using the in tank fuel pump with a regulator on a carbed motor.Now I cut the plug off the e-tranny and ran a test light on all wires and they were all hot with the key on???? there was however 3 wires that looked the same color as the wires for the 700 plug but I dont wanna burn anything up so im looking for advice before I do anything.Heres a few picts I took with my cell to kinda help out.

http://i150.photobucket.com/albums/s...1/hoopty/3.jpg

http://i150.photobucket.com/albums/s...1/hoopty/2.jpg

shortbed70 · 08-04-2009, 10:51 PM

Hey that pic looks familiar I think its mine. I have a pressure swith tapped into the servo cover on the right side of trans and everyone is right about the wiring,top left a lower left d ,a=+,d+-. I have a pos. wire from a to switch and from other side of swith to fused battery sorce and ground to frame. locks up shortly after 4th gear. Some trans are different but if you do some research there are several kits to do this.

**americanmusc1e** · 08-04-2009, 11:26 PM

just kidding,

this is a funny time to bring this up!!! my 700r4 is at the transmission shop because it started leaking around the front seal area, So I took pictures of how it was hooked up when I took the transmission out. BUT MY BROTHER DELETED ALL THE PICTURES I TOOK!!!! so I will have to look it up again.

the inside pin is not used. and one pin should be grounded and one needs a hot wire for lockup.

I'd recommend not using your computer, and hooking the lockup to a toggle switch. you don't need a brake switch or a vacuum switch, and it will lock up in 3rd or 4th gear.

I'll look it up again soon (probably Sunday), right now I'm working 13hr days baling hay and I don't have much time

davidh · 09-05-2011, 02:39 AM

isn't this what a $80 TCI kit does without any switches under the dash for lock or unlocking converter??

03-19-2009, 11:17 AM	#1
americanmusc1e Senior Member Join Date: Jan 2009 Location: Austin, TX Posts: 1,079	700r4 lockup wiring I'm installing a 700r4 in place of my old th350, for the lockup wiring can i run a toggle switch and a brake switch and forget the pressure switch and vacuum switch??? I have an '87 trans out of a camaro and it has a square looking plug with three pins in it, which is power, which is ground and what is the other one for????? thanks in advance __________________ -- Josh Instagram: @americanmusc1e OLD SKOOL-- 1970 C10. 454/Th400/3.07 posi Build Thread FARM TRUCK----1949 Chevrolet 3800 Power Wagon Hauler Build Thread 1999 4wd OBS Tahoe - daily. DM me if you can't see photos i posted

03-19-2009, 12:11 PM	#2
texanidiot25 Eat My Rust Join Date: Jan 2007 Location: Cypress, Texas Posts: 3,362	Re: 700r4 lockup wiring You have to have the TV cable, no matter what.

03-19-2009, 12:55 PM	#3
Indyuke Registered User Join Date: Feb 2008 Location: Lake Stevens, WA Posts: 623	Re: 700r4 lockup wiring Yes, you can run a toggle along with the brake switch instead of a pressure switch. But why? It's much easier to wire up a pressure switch, plus it's much nicer to drive that way. Don't have to think about it. And you don't absolutely need a vac switch. I put one in mine, but bypassed it the first day.

03-19-2009, 01:47 PM	#4
americanmusc1e Senior Member Join Date: Jan 2009 Location: Austin, TX Posts: 1,079	Re: 700r4 lockup wiring anybody know witch one is the "A" pin and witch one is the "D" pin????? __________________ -- Josh Instagram: @americanmusc1e OLD SKOOL-- 1970 C10. 454/Th400/3.07 posi Build Thread FARM TRUCK----1949 Chevrolet 3800 Power Wagon Hauler Build Thread 1999 4wd OBS Tahoe - daily. DM me if you can't see photos i posted

03-19-2009, 02:12 PM	#5
americanmusc1e Senior Member Join Date: Jan 2009 Location: Austin, TX Posts: 1,079	Re: 700r4 lockup wiring which pin do i run the 12 volts to???? and which do i ground???? and what is the third one for???? __________________ -- Josh Instagram: @americanmusc1e OLD SKOOL-- 1970 C10. 454/Th400/3.07 posi Build Thread FARM TRUCK----1949 Chevrolet 3800 Power Wagon Hauler Build Thread 1999 4wd OBS Tahoe - daily. DM me if you can't see photos i posted

03-19-2009, 03:38 PM	#6
71meangreenc10 Its a Truck Thing...... Join Date: Dec 2004 Location: Sierra Vista, Arizona Posts: 3,179	Re: 700r4 lockup wiring Ill look it up this evening if no one els jumps in. Smitty __________________ 71 C10 283/3SPD Full Resto 71 GMC 1500 Sierra Grande http://67-72chevytrucks.com/vboard/s...d.php?t=518599 70 C10 Suburban Former military GSA truck. 72 Chevy Blazer 4X4, Sloppy Jo, Mountain Climber. Wife says no more trucks. http://67-72chevytrucks.com/vboard/s...d.php?t=707378 72 GMC 1 Ton Motor Home, wife said no more trucks until she saw this one. Gen 3 6.0/4L80E 4.10 http://67-72chevytrucks.com/vboard/s...d.php?t=761110 68 GMC Suburban was 3/4 ton, now 1/2.Wife shook her head 71 C30 Wrecker 71 C20 Scott-Bilt As weird as it gets..BB Cheyenne AC Truck 68 GMC Long Stepside. They keep following me home 69 C30 Former Motor Home, Flat Bed time 70 G20 Red-E-Kamp Conversion "I'm your Boogy Van"

03-19-2009, 05:17 PM	#7
michael bustamante Senior Member Join Date: Sep 2007 Location: Albuquerque NM Posts: 7,863	Re: 700r4 lockup wiring the plug should be labled which is which on the underside __________________ 1967custom

03-19-2009, 05:26 PM	#8
cparman sharp as a marble Join Date: Jan 2007 Location: atlantic beach,florida Posts: 1,082	Re: 700r4 lockup wiring the plug will be labeled. If I remember correctly, it will be the terminal in the upper left in your picture. I have a brake light switch, and a toggle, I did it this way so when I am poking along, and the engine is turning too few rpm, I can unlock the converter and eliminate the chuggle in the engine.

03-20-2009, 08:13 AM	#9
Andy4639 Old member Join Date: Jan 2002 Location: Liberty, & Garden City S.C. , U.S. Posts: 19,945	Re: 700r4 lockup wiring I have mine just hooked up with a toggle on the dash. I bought the vacuum switch but just did away with it. It want lock up under 45MPH no way with the B&M kit. I assume you have the internal wiring done already to the transmission for this. I had it done while they built the transmission. __________________ 1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs.

03-20-2009, 08:00 PM	#11
Andy4639 Old member Join Date: Jan 2002 Location: Liberty, & Garden City S.C. , U.S. Posts: 19,945	Re: 700r4 lockup wiring Why do you want a brake switch. Mine works fine even without it. __________________ 1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs.

03-20-2009, 08:12 PM	#13
Indyuke Registered User Join Date: Feb 2008 Location: Lake Stevens, WA Posts: 623	Re: 700r4 lockup wiring Americanmuscle, GENERALLY, power goes to your (A) pin, top left on your pic. Ground is bottom left on your pic, I believe it's (D). And (B) is top right, part of the tranny overheat circuit. The reason I say generally is because GM had like 37 different ways they wired up the TCC. So double check. If you want to control the TCC with a toggle switch, run power to (A) through a toggle switch, and put a jumper between the other two contacts. The torque converter will lockup only when the tranny is in fourth AND you have the toggle flipped on. Wire it up like this without the toggle and the converter will lock up every time it shifts to fourth gear. Hope this helps. Last edited by Indyuke; 03-20-2009 at 08:12 PM.

03-21-2009, 12:21 AM	#14
Indyuke Registered User Join Date: Feb 2008 Location: Lake Stevens, WA Posts: 623	Re: 700r4 lockup wiring I think what andy means is, if it's wired to only lock up in fourth, as soon as you slam on your brakes, the transmission downshifts and the torque converter unlocks. Then when you get going again it upshifts and locks up again. Don't need a brake switch.

03-21-2009, 05:03 AM	#15
Andy4639 Old member Join Date: Jan 2002 Location: Liberty, & Garden City S.C. , U.S. Posts: 19,945	Re: 700r4 lockup wiring Correct if the truck is ever out of fourth gear it want ,Shouldn't lockup at all. I can even back up with the switch on. __________________ 1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs.

03-21-2009, 09:45 AM	#16
LEEVON Moderator Join Date: Jul 2006 Location: Ozark, MO Posts: 4,893	Re: 700r4 lockup wiring If you don't want to mess with a switch, it's only slightly more difficult to put in a vacuum switch and brake cancel switch. I found them to be plentiful at the junkyard and free, I believe I pulled my vacuum switch from a K5, along with a tiny blue vacuum booster. 12v from pin A to the brake cancel switch, then to the vacuum switch and you're all set. __________________ '86 GMC C30 Crew ~ '86 C20 Crew ~ '79 K15 Sierra Grande ~ '76 Blazer 2wd ~ '74K10 ~ '71 Cheyenne swb ~'50 3100 bagged ~ '80 Wife ~ Late model kids

03-21-2009, 09:58 AM	#17
americanmusc1e Senior Member Join Date: Jan 2009 Location: Austin, TX Posts: 1,079	Re: 700r4 lockup wiring thanks guys __________________ -- Josh Instagram: @americanmusc1e OLD SKOOL-- 1970 C10. 454/Th400/3.07 posi Build Thread FARM TRUCK----1949 Chevrolet 3800 Power Wagon Hauler Build Thread 1999 4wd OBS Tahoe - daily. DM me if you can't see photos i posted



Register or Log In To remove these advertisements.

08-04-2009, 08:30 PM	#18
68_c10_on20s Registered User Join Date: Aug 2002 Location: Waxahachie TX Posts: 773	Re: 700r4 lockup wiring Im kinda in the same boat and need some advice.I am going just the opposite route and need help wiring up the 700.My truck is a 93 model and it had a v6 with a 4l60e tranny I had a 350/700 ive installed and need to wire up the lockup now.The 700 only has 3 wires going to it and the e trans had 12. I still have the cpu hooked up only becouse im using the in tank fuel pump with a regulator on a carbed motor.Now I cut the plug off the e-tranny and ran a test light on all wires and they were all hot with the key on???? there was however 3 wires that looked the same color as the wires for the 700 plug but I dont wanna burn anything up so im looking for advice before I do anything.Heres a few picts I took with my cell to kinda help out. http://i150.photobucket.com/albums/s...1/hoopty/3.jpg http://i150.photobucket.com/albums/s...1/hoopty/2.jpg __________________ 93 Fleet Budget Build http://s150.photobucket.com/albums/s...zted71/hoopty/

08-04-2009, 10:51 PM	#19
shortbed70 Registered User Join Date: Mar 2002 Location: Forney TX Posts: 4,512	Re: 700r4 lockup wiring Hey that pic looks familiar I think its mine. I have a pressure swith tapped into the servo cover on the right side of trans and everyone is right about the wiring,top left a lower left d ,a=+,d+-. I have a pos. wire from a to switch and from other side of swith to fused battery sorce and ground to frame. locks up shortly after 4th gear. Some trans are different but if you do some research there are several kits to do this. __________________ Troy 1965 Chevy Bagged,361 sbc,voodoo cam,1.5 full roller rockers,patriot 185cc vortec heads 2.02-1.60,vortec weiand polished intake,demon carb my truckhttp://67-72chevytrucks.com/vboard/s...d.php?t=332884 Big Red Dog build http://67-72chevytrucks.com/vboard/s...d.php?t=572274

08-04-2009, 11:26 PM	#20
americanmusc1e Senior Member Join Date: Jan 2009 Location: Austin, TX Posts: 1,079	Re: 700r4 lockup wiring just kidding, this is a funny time to bring this up!!! my 700r4 is at the transmission shop because it started leaking around the front seal area, So I took pictures of how it was hooked up when I took the transmission out. BUT MY BROTHER DELETED ALL THE PICTURES I TOOK!!!! so I will have to look it up again. the inside pin is not used. and one pin should be grounded and one needs a hot wire for lockup. I'd recommend not using your computer, and hooking the lockup to a toggle switch. you don't need a brake switch or a vacuum switch, and it will lock up in 3rd or 4th gear. I'll look it up again soon (probably Sunday), right now I'm working 13hr days baling hay and I don't have much time __________________ -- Josh Instagram: @americanmusc1e OLD SKOOL-- 1970 C10. 454/Th400/3.07 posi Build Thread FARM TRUCK----1949 Chevrolet 3800 Power Wagon Hauler Build Thread 1999 4wd OBS Tahoe - daily. DM me if you can't see photos i posted

09-05-2011, 02:39 AM	#21
davidh Senior Member Join Date: Feb 2004 Location: Ponca city now kingfisher Oklahoma Posts: 1,220	Re: 700r4 lockup wiring isn't this what a $80 TCI kit does without any switches under the dash for lock or unlocking converter?? __________________ Even the nicest dodge-chrysler is only 2years away from being parked outside of Section 8 housing.

Register or Log In To remove these advertisements.