Ignition Switch Wiring Harness 1977 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Richard D · 01-25-2010, 04:44 PM

I have a '77 GMC with some melted wires under the steering column. Can I replace just that part of the harness, without buing a complete(expensive) harness?

glock35ipsc · 01-25-2010, 05:09 PM

You probably could, but you would need to find out why they melted in the first place so it doesn't happen again.

Richard D · 01-26-2010, 12:32 AM

This thing is over thirty years old, has lots of splices and speaker wire up under the dash and hood. There were splices wrapped in duct tape instead of electrical tape, and the you have to push a button under the dash after turning the key on to start it. LOTS of jury-rigged stuff on this thing. I'd love to replace the entire wiring harness, which I someday will, but I am unemployed at the moment and need to drive this thing.

glock35ipsc · 01-26-2010, 01:41 PM

You might start looking in the parts section here, and you local junk yards for an entire under dash harness, and maybe an under hood harness. If that is not possible ($$$ wise) I would methodically start replacing each necessary wire.

01-25-2010, 04:44 PM	#1
Richard D Registered User Join Date: Jun 2008 Location: Texas Ctiy TX Posts: 228	Ignition Switch Wiring Harness 1977 I have a '77 GMC with some melted wires under the steering column. Can I replace just that part of the harness, without buing a complete(expensive) harness?

01-25-2010, 05:09 PM	#2
glock35ipsc Next project: 1970 K10 Join Date: Feb 2004 Location: Fort Collins, Colo 80524 Posts: 6,684	Re: Ignition Switch Wiring Harness 1977 You probably could, but you would need to find out why they melted in the first place so it doesn't happen again. __________________ *Bob* 1970 Chevy K10 LWB "Goldie" 350/TH350 *next project!!* 1981 Chevy C10 LWB 355/TH350 - My son's truck LS SWAP FORUM! Tons of LS swap info here! PLEASE CLICK HERE TO SUPPORT THE GREATEST BOARD ON THE NET! CLICK HERE FOR THE FAQ INDEX by KRUE

01-26-2010, 12:32 AM	#3
Richard D Registered User Join Date: Jun 2008 Location: Texas Ctiy TX Posts: 228	Re: Ignition Switch Wiring Harness 1977 This thing is over thirty years old, has lots of splices and speaker wire up under the dash and hood. There were splices wrapped in duct tape instead of electrical tape, and the you have to push a button under the dash after turning the key on to start it. LOTS of jury-rigged stuff on this thing. I'd love to replace the entire wiring harness, which I someday will, but I am unemployed at the moment and need to drive this thing.

01-26-2010, 01:41 PM	#4
glock35ipsc Next project: 1970 K10 Join Date: Feb 2004 Location: Fort Collins, Colo 80524 Posts: 6,684	Re: Ignition Switch Wiring Harness 1977 You might start looking in the parts section here, and you local junk yards for an entire under dash harness, and maybe an under hood harness. If that is not possible ($$$ wise) I would methodically start replacing each necessary wire. __________________ *Bob* 1970 Chevy K10 LWB "Goldie" 350/TH350 *next project!!* 1981 Chevy C10 LWB 355/TH350 - My son's truck LS SWAP FORUM! Tons of LS swap info here! PLEASE CLICK HERE TO SUPPORT THE GREATEST BOARD ON THE NET! CLICK HERE FOR THE FAQ INDEX by KRUE



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.