Chevy HEI distributor types - The 1947 - Present Chevrolet & GMC Truck Message Board Network

skysoldier173rd · 09-06-2010, 05:24 PM

Does anyone know much about a gm ESC type distrubutor? Just wondering if this one takes a module. It has a 4 wire cable going into the base. I inherited it with the sbc engine i put in my 60. Just wondering if it takes a module, if not how does it get wired. Any help will be greatly appreciated. Didn't notice any modules when i pulled the engine for transplant, but didn't pay a lot of attention to wires.

www.picturetrail.com/skysoldier173rd

**Captainfab** · 09-07-2010, 12:59 AM

I don't know much about them, other than they can be a pos in the original installation. But I believe this is mainly caused by the ESC box on the firewall. There was another member having problems with his in his '86(?) truck over in the 'Engine and Drivetrain' section not long ago. Member cableguy0 helped him get it figured out and running much better. You might try sending cableguy0 a PM and see what he has to say as he seems to be knowledgeable on these distributors.

skysoldier173rd · 09-07-2010, 06:28 AM

I did a little reading on them yesterday after the post and i guess you can run a jumper between two of the wires and cancel the esc module, but the timing stays at base and will not advance properly when engine accellerates. Also wrecks the mileage. Think I'm just going to pick up a pre-esc unit at a bone yard. This thing just isn't worth the hassle and used ones are cheap, so problem solved, but thanks for your input.

www.picturetrail.com/skysoldier173rd

09-06-2010, 05:24 PM	#1
skysoldier173rd Registered User Join Date: May 2010 Location: jackson, michigan Posts: 246	Chevy HEI distributor types Does anyone know much about a gm ESC type distrubutor? Just wondering if this one takes a module. It has a 4 wire cable going into the base. I inherited it with the sbc engine i put in my 60. Just wondering if it takes a module, if not how does it get wired. Any help will be greatly appreciated. Didn't notice any modules when i pulled the engine for transplant, but didn't pay a lot of attention to wires. www.picturetrail.com/skysoldier173rd

09-07-2010, 12:59 AM	#2
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,252	Re: Chevy HEI distributor types I don't know much about them, other than they can be a pos in the original installation. But I believe this is mainly caused by the ESC box on the firewall. There was another member having problems with his in his '86(?) truck over in the 'Engine and Drivetrain' section not long ago. Member cableguy0 helped him get it figured out and running much better. You might try sending cableguy0 a PM and see what he has to say as he seems to be knowledgeable on these distributors. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

09-07-2010, 06:28 AM	#3
skysoldier173rd Registered User Join Date: May 2010 Location: jackson, michigan Posts: 246	Re: Chevy HEI distributor types I did a little reading on them yesterday after the post and i guess you can run a jumper between two of the wires and cancel the esc module, but the timing stays at base and will not advance properly when engine accellerates. Also wrecks the mileage. Think I'm just going to pick up a pre-esc unit at a bone yard. This thing just isn't worth the hassle and used ones are cheap, so problem solved, but thanks for your input. www.picturetrail.com/skysoldier173rd



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.