The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain > LSx Swaps

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 02-13-2011, 01:37 PM   #1
azsmokey
Registered User
 
Join Date: Dec 2007
Location: Glendale, AZ
Posts: 156
PCM programming in Phoenix, AZ

Can anyone recommend a reputable shop/person that can assist us with reprogramming our PCM?

We have a 72 K-10 with a Vortech SC'd 6.0/4L65E/NP205 combo. We used the Painless 60221 powertrain harness. Painless states that the PCM needs reprogramming prior to successful startup. At this point the engine cranks and all systems appear nominal, however it will not run. Unless I missed something, which is quite possible, I probably should have the PCM done.

Any ideas, comments, suggestions?

Thanks
azsmokey is offline   Reply With Quote
Old 02-13-2011, 01:39 PM   #2
67C10BUB
Registered User
 
67C10BUB's Avatar
 
Join Date: Aug 2010
Location: Alta Loma, CA
Posts: 610
Re: PCM programming in Phoenix, AZ

I thought that Painless included ECM tuning with the purchase of their harness. If not then I went with Speartech and have been happy so far.
__________________
67 5.3L Build
67C10BUB is offline   Reply With Quote
Old 02-13-2011, 03:13 PM   #3
Clyde65
1965 Chevy C10, 2005 4.8L/4l60
 
Clyde65's Avatar
 
Join Date: Aug 2004
Location: DFW Texas
Posts: 8,546
Re: PCM programming in Phoenix, AZ

Nelson Performance is who I am going with, they are in San Antonio.

http://www.nelsonperformance.com/NPTuneInfo.htm
__________________
Clyde65

Rebuild of Clyde
http://67-72chevytrucks.com/vboard/s...84#post8338184

69 Aristocrat Lo Liner build
http://67-72chevytrucks.com/vboard/s...84#post7561684



support our troops!
Clyde65 is offline   Reply With Quote
Old 02-13-2011, 05:32 PM   #4
azsmokey
Registered User
 
Join Date: Dec 2007
Location: Glendale, AZ
Posts: 156
Re: PCM programming in Phoenix, AZ

Quote:
I thought that Painless included ECM tuning with the purchase of their harness. If not then I went with Speartech and have been happy so far.
They do include PCM reprogramming with the purchase of the harness. However, I would prefer to have someone in the Phoenix area handle that task for a multitude of reasons. If that is not possible I will send it out.
azsmokey is offline   Reply With Quote
Old 02-13-2011, 06:23 PM   #5
67C10BUB
Registered User
 
67C10BUB's Avatar
 
Join Date: Aug 2010
Location: Alta Loma, CA
Posts: 610
Re: PCM programming in Phoenix, AZ

I don't know of anyone in AZ.
Posted via Mobile Device
__________________
67 5.3L Build
67C10BUB is offline   Reply With Quote
Old 02-14-2011, 03:30 AM   #6
matthew20061
69' Chevy Stepside
 
matthew20061's Avatar
 
Join Date: Mar 2008
Location: Anchorage, Ak
Posts: 526
Re: PCM programming in Phoenix, AZ

Try this place, I believe a guy named zippy (Mike) works there, he's been tuning for a very long time and very good at it. He did the tune for my truck over the phone for the 5.3L with a cam and now for the modded 6.0L. I contacted him directly, via Silveradoss.com username zippy. Here's the link for the place he works: http://www.adsautorepair.com/hp_customtuning.htm
__________________
-Matthew
-69' Chevy Custom/10 Shortbed Stepside 2WD "Copperhead"
- Restored, 6.0L LQ9 Built. L92 Heads and LS3 Intake with Comp Cam 223/231 .610/.617 112 LSA, 4L60E with Shift Kit and Circle-D 3200 Stall Converter ~Build Thread
-1957 Chevy BelAir 2 Door Post Sedan, Full Frame off Restoration done myself - 6.0L with T56 six speed
-1957 Chevy BelAir 2 Door Post Sedan - Nearly rust free AK car, Project in the waiting
-2003' Chevy Silverado SS AWD 6.0L! - Daily Driver

Last edited by matthew20061; 02-14-2011 at 03:31 AM.
matthew20061 is offline   Reply With Quote
Old 02-15-2011, 06:02 AM   #7
c10seconds
Registered User
 
c10seconds's Avatar
 
Join Date: Oct 2009
Location: gilbert,AZ
Posts: 947
Re: PCM programming in Phoenix, AZ

If you haven't found anybody go to arizona dyno chip and they'll hook you up.
Posted via Mobile Device
c10seconds is offline   Reply With Quote
Old 02-18-2011, 11:42 PM   #8
68 c10 ls2
Registered User
 
68 c10 ls2's Avatar
 
Join Date: Mar 2010
Location: Minnesota
Posts: 157
Re: PCM programming in Phoenix, AZ

Quote:
Originally Posted by matthew20061 View Post
Try this place, I believe a guy named zippy (Mike) works there, he's been tuning for a very long time and very good at it. He did the tune for my truck over the phone for the 5.3L with a cam and now for the modded 6.0L. I contacted him directly, via Silveradoss.com username zippy. Here's the link for the place he works: http://www.adsautorepair.com/hp_customtuning.htm
Please go se Zippy!!!! He does AWSOME work!! He is tuning my truck via e-mail and tuned my buddys LSX427 Suburban (1000hp, 725hp to the wheels). Zippy is the BEST when it comes to tuning any setup!! You will be very happy!!!
68 c10 ls2 is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:34 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com