For all the racers looking for a 400ci SBC

[1Bad62Pro/Street]

1970 Chevy 400 cu in SB, Casting 3951511 Canadian Block
http://67-72chevytrucks.com/vboard/s...07#post4900807

[C-10 simplex]

If i could ask a related question; Are the new bowtie sportsman blocks such as 12480175, 12480157 and 159 actual 400 blocks?

What i'm trying to get at is are these essentially "new 400" blocks as an alternative to looking for and buying used?

[1Bad62Pro/Street]

Originally Posted by C-10 simplex

If i could ask a related question; Are the new bowtie sportsman blocks such as 12480175, 12480157 and 159 actual 400 blocks?

What i'm trying to get at is are these essentially "new 400" blocks as an alternative to looking for and buying used?

I think there are just 350 blocks made into 400 cubic inch.
http://www.jrgmparts.com/GM_Performa...y_small_b.html

GM Performance 12480175 - GM Performance 350 C.I.D. Cast Iron Racing Bowtie Bare Engine Blocks
http://www.summitracing.com/parts/NAL-12480175/

GM Performance 12480157 - GM Performance Bowtie Sportsman Engine Blocks
http://www.summitracing.com/parts/NAL-12480157/

GM Performance 12480159 - GM Performance 350 C.I.D. Cast Iron Racing Bowtie Bare Engine Blocks
http://www.summitracing.com/parts/NAL-12480159/

[C-10 simplex]

i.c., so this could be an alternative to getting 400+ cubes AND have all the advantages of a 383 stroker because these blocks can also take a 3.75" or greater crank?

So this could be an alternative to trying to find a good 400 block? i know that the bowties probably cost at least 2K, but when you consider the time savings etc.........?

[dbmx66]

Originally Posted by C-10 simplex

i.c., so this could be an alternative to getting 400+ cubes AND have all the advantages of a 383 stroker because these blocks can also take a 3.75" or greater crank?

So this could be an alternative to trying to find a good 400 block? i know that the bowties probably cost at least 2K, but when you consider the time savings etc.........?

you just have to watch how much you bore and stroke it, on 400 blocks the cylinders are very close together. and if you need to clearance the block for a larger than 3.75 stoke your gonna be in the water jacket. unless you do it carefully.

[C-10 simplex]

i guess what i'm trying to get at is maybe this could be a way to get 400 cubes in a small block without trying to hunt down an actual original 400 block.


i know the price is a little steep but it could save a lot of time---what if you did manage to find an original 400 block only to find that it's too cracked up?

[Marv D]

1bad,, actually sorry dude, didn't realize it ws you that had a GM block for sale in the listing. Wouldn't have harped on the GM casitngs if I had realized,, now I cn't fricking edit it!

DOH!!!

[1Bad62Pro/Street]

No problem Bud.
It's all good.
I'm selling this for my dad. It was gave to him for some work that was done.
Alot of guys love these 400's for racing. So I just posted it here just just in case there were anyone in NC/SC folks that lived close buy.

Casting # CID Year Model Application Comments
3951511 400 70-73 Pass,Chevelle,Monte 4 bolt main, 3 freeze plugs/side
3951511 400 75-80 Truck 4 bolt main, 3 freeze plugs/side


Chevy 400 cu in SB out of a Chevy K-20
.030 over Good Hone No Land
Casting 3951511 Canadian 4 Bolt Main Block
3 Freeze Plugs
Balanced Rotating Assembly
I-Beam Rods Cleared for High Lift Cam
COR Hypertec Aluminum pistons Dish Type
.010 cast crank 3951528 - Low miles
Good Clean Polished Finish
needs Decked and some Heli-Coils Installed

$400.00 OBO
NC 1970 Chevy 400 cu in SB, Casting 3951511 Canadian Block
http://67-72chevytrucks.com/vboard/s...07#post4900807
1bad62prostreet@gmail.com