Pre bent brakeline kits?

[tj62]

Finally got everything straight and ready to test drive, drove around the yard and blew a brake line, glad I did it in the yard instead of on the road. I'm going to replace all my brake lines just to be safe, but all the bending looks tricky and tough, but doable. I installed a new line to my clutch slave cylinder, not too bad.

Has anyone used the pre bent brake line kits from LMC or similar? Wondering if they're any easier or worth it?

[litew8]

Yes, I've just installed them. Haven't tested, but they were worth the price to me, saved time. Some have gotten good results from inlinetube.com/, I think I had read that Inlinetube gets their stuff from getdiscbrakes.com/, which is where I ordered mine from. They shipped to the wrong state, and when I finally did get them, the two small lines that come off of the Master Cylinder seemed backwards so I didn't try and replace those two. But everything else fit nice.

[Robznob11]

3 /16 line bends super easy by hand and is dirt cheap with flares and ends on already. I bent up my own in a short time. the master lines take special nuts and one line is quarter and one 3 /16 so its hard to get them backwards. Id say impossible caus the 1/4 line has two different ends and the 3/16 has matching ends.

[litew8]

I mean backwards as in bent backwards, as in - for the wrong truck. Good luck bending, flaring etc... I never said it would be hard, just time consuming.
Oh and my lines are like the Original Manufacture lines, with ribbing around specific areas, how about yours, are they HD?

[ItsRandy]

Bend your own. I wish I would have. InLine Tube stainless didn't fit very well. They said it was my fault.

[Robznob11]

napa sells the lines with springs on them like the oe. that actually keeps you from kinking them when you bend them. a 51" line is about 6 bucks and that for a coated one that will last for ever. they have flares and ends on them already so all you need to buy is invert butt connectors. I did my back line new across the rear one 41" line and one 20" line and i run a rubber brake hose for a 98 3500 truck caus it has the t built on and is 22" all that together hose and all cost me 35" bucks and the hose was 24 of that. Id say you could plum your whole system for around 60 bucks. as a tip if you measure 40 " get no more than 41" line cause you cant put enough bends in to eat up more than an inch of line. and it will look much better with less bends you can get a tube bender at hf for a few dollars but i bent most of mine by hand unless i needed and true 90*

[funkytechmonkey]

Originally Posted by ItsRandy

Bend your own. I wish I would have. InLine Tube stainless didn't fit very well. They said it was my fault.

I had the same problem and they said the same thing... sending mine back and ordering all the stuff to bend my own

[truckdude239]

i used www.inlinetube.com for mine

[D13]

I walked in the door at inline and walked out 5 minutes later with the prebent rear line for my 87 longbed. By time I buy the tube, cut to length, make all the funky bends for a dual tank diesel, flare the cut end, etc, the price of the prebent was cheaper than parts + time.

At $189 or so for complete stainless line set, that's where I'm going for my rebuild. That much tube would probably be $50 and if it saves me 3 hours of annoyance I'd consider the rest well spent.

[Tony@AirRideTech]

Here is the really easy way to answer that question.... If you dont have descent bending tools and you dont intend on bending anymore lines... then purchase a pre bent line set. personally I like bending my own lines but then again, I have descent tools to do it.

[tubbedII]

Originally Posted by Tony@AirRideTech

Here is the really easy way to answer that question.... If you dont have descent bending tools and you dont intend on bending anymore lines... then purchase a pre bent line set. personally I like bending my own lines but then again, I have descent tools to do it.

This was my problem. I didn't have a good flaring tool. I actually was able to borrow one for the few flares I needed to do, and a good tool made my experience from impossible to easy. Still, I don't think I would have liked to bend the lines on the front crossmember...looked like a PITA.

[Tony@AirRideTech]

Originally Posted by tubbedII

This was my problem. I didn't have a good flaring tool. I actually was able to borrow one for the few flares I needed to do, and a good tool made my experience from impossible to easy. Still, I don't think I would have liked to bend the lines on the front crossmember...looked like a PITA.

Ought to try bending fuel line for a stovebolt that follows the contour of the valve cover, clears the water neck inlet, bends around the side and clears factory horn....

[tubbedII]

Originally Posted by Tony@AirRideTech

Ought to try bending fuel line for a stovebolt that follows the contour of the valve cover, clears the water neck inlet, bends around the side and clears factory horn....

Haha! Shoot...I'm leary on bending simple one from my fuel pump to the carb on my 350...

[maskale]

bend ur own all the way. much cheaper and u can bend the way u want.



http://67-72chevytrucks.com/vboard/s...d.php?t=478219