Just alittle lift - The 1947 - Present Chevrolet & GMC Truck Message Board Network

iceship · 10-29-2011, 09:44 PM

87 c10. 2.5 spindels and 2in drop coils...... I'm just a bit to low for the rims I got ... Big boy 24, but was jut looking for 22... So I need to go up 1in or 1.5in.... Has anyone used the twist in spacers from autozone or advance.... How many did u use to get the clearance you need...

To LOW

To HIGH

SCOTI · 10-30-2011, 03:24 AM

Energy Suspension made a urethane coil spacer that was 1" @ one point in time. Check them out & see if it's still avail before using those 'twist-in' style spacers for the coils.

iceship · 10-30-2011, 08:45 PM

So I put a set of coil booster on they are just a tad less than 1.5in..... so it is lower then stock just a bit... it my settle some more... it not ill cut .5in off....

tubbedII · 10-31-2011, 01:22 PM

Which type of coil booster did you use? The knuckles or the black rubberish spacer? If you got the rubber type, don't cut a coil because it'll eventually break down and your ride height will go back to what it was, and if you cut it'll be even lower.

I think Belltech makes a poly one too that goes on top of the spring rather than inbetween. I have one on my s10 to level it out, but don't see why you couldn't put 1 on each side.

iceship · 10-31-2011, 08:49 PM

I got the rubber one you put on the bottom but u can put them in between..... the drivers side is just right, other side is a inch high...
Ill keep my eye out for the other ones...

10-29-2011, 09:44 PM	#1
iceship Registered User Join Date: Apr 2011 Location: bowling green, ky Posts: 439	Just alittle lift 87 c10. 2.5 spindels and 2in drop coils...... I'm just a bit to low for the rims I got ... Big boy 24, but was jut looking for 22... So I need to go up 1in or 1.5in.... Has anyone used the twist in spacers from autozone or advance.... How many did u use to get the clearance you need... To LOW To HIGH

10-30-2011, 03:24 AM	#2
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,068	Re: Just alittle lift Energy Suspension made a urethane coil spacer that was 1" @ one point in time. Check them out & see if it's still avail before using those 'twist-in' style spacers for the coils. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

10-30-2011, 08:45 PM	#3
iceship Registered User Join Date: Apr 2011 Location: bowling green, ky Posts: 439	Re: Just alittle lift So I put a set of coil booster on they are just a tad less than 1.5in..... so it is lower then stock just a bit... it my settle some more... it not ill cut .5in off....

10-31-2011, 01:22 PM	#4
tubbedII needs more $$$ Join Date: Mar 2004 Location: Sacramento Posts: 1,936	Re: Just alittle lift Which type of coil booster did you use? The knuckles or the black rubberish spacer? If you got the rubber type, don't cut a coil because it'll eventually break down and your ride height will go back to what it was, and if you cut it'll be even lower. I think Belltech makes a poly one too that goes on top of the spring rather than inbetween. I have one on my s10 to level it out, but don't see why you couldn't put 1 on each side. __________________ 1970 2wd Blazer

10-31-2011, 08:49 PM	#5
iceship Registered User Join Date: Apr 2011 Location: bowling green, ky Posts: 439	Re: Just alittle lift I got the rubber one you put on the bottom but u can put them in between..... the drivers side is just right, other side is a inch high... Ill keep my eye out for the other ones...



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.