The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1947 - 1959 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 05-01-2012, 09:33 PM   #1
vjjack04
Registered User
 
vjjack04's Avatar
 
Join Date: Jun 2010
Location: Bear Grass, NC
Posts: 291
Radiator

ok, now that I know I am inclined to change out my factory 55 radiator, does anybody have experience with a good radiator? I already had a suggestion or two. The current radiator is about 25 1/2 tall, 21 3/4 wide, 2 1/8 think and from mounting tab end to end is about 26 1/2 inches. Summit sells some aluminum racing/circle track radiators that would work - I want to mount it to the factory area and probably remove the "x" small bars in the front and have pusher type dual fans...comments welcome.

Also, I will have an original factory 55 chevy radiator for sell....
vjjack04 is offline   Reply With Quote
Old 05-02-2012, 12:11 AM   #2
OrrieG
Registered User
 
OrrieG's Avatar
 
Join Date: Jun 2006
Location: Idaho
Posts: 8,800
Re: Radiator

I put a big truck (2 ton) radiator in mine, mounted in the 6 cylinder location. It is 1 inch thicker and a little longer than the stock 6 cylinder one. It bolts to the stock mounting points. I ran a stock 6 cylinder radiator and never had any cooling problems, even creeping around in the hills, but figured with the AC I should upgrade. I got it in a trade so cost was not an issue. Shroud is from a mid 70's GM.
Attached Images
 
__________________
1959 Chevy Short Fleetside w/ 74 4WD drive train (current project) OrrieG Build Thread
1964 Chevelle Malibu w/ 355-350TH (daily driver)
Helpful AD and TF Manual Site Old Car Manual Project
OrrieG is offline   Reply With Quote
Old 05-02-2012, 12:40 AM   #3
parkwood
Registered User
 
parkwood's Avatar
 
Join Date: Jul 2011
Location: shingle springs, calif
Posts: 771
Re: Radiator

I used a radiator from U.S. Radiator.. fit great and did the job.. and you're right you will have to lose the cross bars for the pusher fan..
Attached Images
    
parkwood is offline   Reply With Quote
Old 05-02-2012, 06:02 PM   #4
candyx
Registered User
 
candyx's Avatar
 
Join Date: Aug 2010
Location: somerville nj
Posts: 194
Re: Radiator

I used a PRC radiator with trans cooler,good construction and quality and left me just enough room for the puller electric fan.

http://www.prchotrod.com/products/index.php
candyx is offline   Reply With Quote
Old 05-02-2012, 09:42 PM   #5
Denee007
Senior Member
 
Denee007's Avatar
 
Join Date: May 2011
Location: Cypress, Tx.
Posts: 1,504
Re: Radiator

Hi, are the crossbars necessary? Ill be installing Ac, just wondering if they'll be in the way?

Quote:
Originally Posted by parkwood View Post
I used a radiator from U.S. Radiator.. fit great and did the job.. and you're right you will have to lose the cross bars for the pusher fan..
Denee007 is offline   Reply With Quote
Old 05-02-2012, 11:45 PM   #6
vjjack04
Registered User
 
vjjack04's Avatar
 
Join Date: Jun 2010
Location: Bear Grass, NC
Posts: 291
Re: Radiator

Guys,
Thanks, some good info here. I am surprised too because after I posted this I saw the other aluminum radiator thread...which has some good info too....
Posted via Mobile Device
vjjack04 is offline   Reply With Quote
Old 05-03-2012, 12:16 PM   #7
G&R's57GMC
Senior Member
 
G&R's57GMC's Avatar
 
Join Date: Aug 2010
Location: Shasta Lake, CA.
Posts: 1,624
Re: Radiator

Quote:
Originally Posted by Denee007 View Post
Hi, are the crossbars necessary? Ill be installing Ac, just wondering if they'll be in the way?
The cross bars stiffen the core support. If you remove them its best to run a weld on all the side panels of the core support to add back some of the ridgeity lost. Remember the core support also supports the entire front clip from racking.

You should not have to remove the X to install A/C.

The condenser should have an air gap between the Rad.

Pusher Fans are not as effective as puller fans.
G&R's57GMC is offline   Reply With Quote
Old 05-03-2012, 01:06 PM   #8
Denee007
Senior Member
 
Denee007's Avatar
 
Join Date: May 2011
Location: Cypress, Tx.
Posts: 1,504
Re: Radiator

Thanks! I didn't think anyone saw my question~ ; )

Quote:
Originally Posted by G&R's57GMC View Post
The cross bars stiffen the core support. If you remove them its best to run a weld on all the side panels of the core support to add back some of the ridgeity lost. Remember the core support also supports the entire front clip from racking.

You should not have to remove the X to install A/C.

The condenser should have an air gap between the Rad.

Pusher Fans are not as effective as puller fans.
Denee007 is offline   Reply With Quote
Old 05-03-2012, 12:13 AM   #9
vjjack04
Registered User
 
vjjack04's Avatar
 
Join Date: Jun 2010
Location: Bear Grass, NC
Posts: 291
Re: Radiator

Quote:
Originally Posted by parkwood View Post
I used a radiator from U.S. Radiator.. fit great and did the job.. and you're right you will have to lose the cross bars for the pusher fan..
Nice, what fan is that?
Posted via Mobile Device
vjjack04 is offline   Reply With Quote
Old 05-03-2012, 01:10 AM   #10
55Cameo
Registered User
 
55Cameo's Avatar
 
Join Date: Apr 2011
Location: Tucson, Arizona
Posts: 151
Re: Radiator

I have a great set up from Summit in mine. I just had to have some custom brackets made, no biggie, and its works great. Never gets hot and overkill even for our AZ heat.

My opinion would be pullers work way better then pushers. The fans just block air being in front. I;m sure you should have the space since you motor is close to the firewall


__________________
Build thread:55 Cameo R!! http://67-72chevytrucks.com/vboard/s...d.php?t=519851
55Cameo is offline   Reply With Quote
Old 05-03-2012, 01:59 PM   #11
vjjack04
Registered User
 
vjjack04's Avatar
 
Join Date: Jun 2010
Location: Bear Grass, NC
Posts: 291
Re: Radiator

[QUOTE=55Cameo;5350245]I have a great set up from Summit in mine. I just had to have some custom brackets made, no biggie, and its works great. Never gets hot and overkill even for our AZ heat.

My opinion would be pullers work way better then pushers. The fans just block air being in front. I;m sure you should have the space since you motor is close to the firewall

55 Cameo - How wide is that radiator and which model is it - also do you have the width with the fans - at least and estimate (oh and what model are the fans from summit?)
vjjack04 is offline   Reply With Quote
Old 05-02-2012, 06:48 PM   #12
G&R's57GMC
Senior Member
 
G&R's57GMC's Avatar
 
Join Date: Aug 2010
Location: Shasta Lake, CA.
Posts: 1,624
Re: Radiator

I'm using a 2000 Camero Rad and fan set up and a 5.3 L

Makes for a tight package. Simple upper mount, small cut on core support bracket, light weight and inexpensive. All new way cheaper then aftermarket hot rod parts. Fan assembly $165, rad. $180.
Attached Images
    
G&R's57GMC is offline   Reply With Quote
Old 05-11-2012, 10:50 AM   #13
vjjack04
Registered User
 
vjjack04's Avatar
 
Join Date: Jun 2010
Location: Bear Grass, NC
Posts: 291
Re: Radiator

Quote:
Originally Posted by G&R's57GMC View Post
I'm using a 2000 Camero Rad and fan set up and a 5.3 L

Makes for a tight package. Simple upper mount, small cut on core support bracket, light weight and inexpensive. All new way cheaper then aftermarket hot rod parts. Fan assembly $165, rad. $180.
G&R what size radiator is that?
vjjack04 is offline   Reply With Quote
Old 05-02-2012, 08:44 PM   #14
Daze57
Registered User
 
Daze57's Avatar
 
Join Date: Jul 2011
Location: Las Vegas - Nev. aka Sin City
Posts: 1,835
Re: Radiator

i had a good radiator/machine shop rebuild my original rad. to a 4 core - they went through it completly - than i added a sidewinder puller fan that pulls 'bout 3000 cfm .
livin here in sin city we do get our hot days - but i think the new set up will wrk out
Daze57 is offline   Reply With Quote
Old 05-03-2012, 12:01 AM   #15
azsnow
Registered User
 
azsnow's Avatar
 
Join Date: Nov 2008
Location: Usa
Posts: 150
Re: Radiator

G&R, is that the same truck as in your avatar? If so, I would have never expected to find that under the hood! Love it!
azsnow is offline   Reply With Quote
Old 05-03-2012, 01:44 AM   #16
G&R's57GMC
Senior Member
 
G&R's57GMC's Avatar
 
Join Date: Aug 2010
Location: Shasta Lake, CA.
Posts: 1,624
Re: Radiator

Quote:
Originally Posted by azsnow View Post
G&R, is that the same truck as in your avatar? If so, I would have never expected to find that under the hood! Love it!
Short answer, no. I saw it at a show and asked a lot of questions.

So its what I'm using on the chassis I'm building to go under the body of my avatar. Changing from Napco 4x4 to 2x4 air ride 5.3L 4L60E Currie 9".

You can see it stuffed in the corner, the pic subject is about the trailer I redoing.
Attached Images
  
G&R's57GMC is offline   Reply With Quote
Old 05-03-2012, 03:18 AM   #17
zonacat00
Registered User
 
zonacat00's Avatar
 
Join Date: Dec 2011
Location: Tucson, AZ
Posts: 7
Re: Radiator

I'm currently having the original 47 radiator flushed and repaired. Not cheap. Close to $500.
zonacat00 is offline   Reply With Quote
Old 05-03-2012, 01:29 PM   #18
_Ogre
Registered User
 
_Ogre's Avatar
 
Join Date: Jan 2012
Location: Motown
Posts: 7,680
Re: Radiator

not a good picture but the best i had on photobucket
i kept the crossbars and installed a vintage air 55-59 sure fit condenser and hard lines
those crossbars are the only thing keeping the front sheet metal from racking side to side.
the us radiator that parkwood has is also the one that brothers sells (i have one) it drop ships from us radiator
mine is the desert cooler with trans cooler in the bottom tank

__________________
cool, an ogre smiley Ogre's 58 Truk build

how to put your truck year and build thread into your signature
shop air compressor timer
_Ogre is offline   Reply With Quote
Old 05-08-2012, 12:21 PM   #19
55Cameo
Registered User
 
55Cameo's Avatar
 
Join Date: Apr 2011
Location: Tucson, Arizona
Posts: 151
Re: Radiator

Yeah no prob man. Always glad to help.I still need to take you up on your offer and come check out that truck of yours
__________________
Build thread:55 Cameo R!! http://67-72chevytrucks.com/vboard/s...d.php?t=519851
55Cameo is offline   Reply With Quote
Old 05-08-2012, 12:34 PM   #20
vjjack04
Registered User
 
vjjack04's Avatar
 
Join Date: Jun 2010
Location: Bear Grass, NC
Posts: 291
Re: Radiator

Quote:
Originally Posted by 55Cameo View Post
Yeah no prob man. Always glad to help.I still need to take you up on your offer and come check out that truck of yours
Yep, and maybe you would have other good bits of advice...thanks again.
vjjack04 is offline   Reply With Quote
Old 05-08-2012, 12:50 PM   #21
55Cameo
Registered User
 
55Cameo's Avatar
 
Join Date: Apr 2011
Location: Tucson, Arizona
Posts: 151
Re: Radiator

Yeah for sure, be great to bounce ideas off each other about the trucks. I have some PTO at worked I haven't used, could make a small road trip with the wife up there. I'll hit you up and make some plans one soon
__________________
Build thread:55 Cameo R!! http://67-72chevytrucks.com/vboard/s...d.php?t=519851
55Cameo is offline   Reply With Quote
Old 05-10-2012, 12:11 AM   #22
vjjack04
Registered User
 
vjjack04's Avatar
 
Join Date: Jun 2010
Location: Bear Grass, NC
Posts: 291
Re: Radiator

Quote:
Originally Posted by 55Cameo View Post
Yeah for sure, be great to bounce ideas off each other about the trucks. I have some PTO at worked I haven't used, could make a small road trip with the wife up there. I'll hit you up and make some plans one soon
Sure, let me know. I am home most weekends and some Fridays.
Posted via Mobile Device
vjjack04 is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:28 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com