|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
05-14-2012, 07:05 PM
|
#1 |
|
Registered User
Join Date: May 2012
Location: Visalia CA
Posts: 118
|
To all who keep asking on battery placement
1300 cold cranking amps, summits remote kit, arco solar charger.
Take that 120 lbs and put it where it counts!   Posted via Mobile Device |
|
|
|
05-14-2012, 07:24 PM
|
#2 |
|
Registered User
Join Date: Mar 2012
Location: edgartown mass
Posts: 852
|
Re: To all who keep asking on battery placement
are those both 1300 cca? and are you shure that its not 1300 ca? not saying its not but i would like them for my diesel. thanks, mike
|
|
|
|
|
05-14-2012, 07:31 PM
|
#3 | |
|
Registered User
Join Date: May 2012
Location: Visalia CA
Posts: 118
|
Re: To all who keep asking on battery placement
Quote:
Btw. To all! Make sure u use a saftey disconnect. My setup in this pic dones not yet have one. With 1000amps grounding... Oh boy. Thats a welder and quickly a bomb. 86c20: i reccomend u research how many amps ur starter draws, and compair it to the national wire guage chart to estimate if summits kit is big enough, mines right at the limit of 300a on this line with DIRECT FRAME CONTACT. You may need to order 2 kits and run two positives to the starter to support that amperage draw. Posted via Mobile Device |
|
|
|
|
|
05-14-2012, 07:33 PM
|
#4 |
|
Registered User
Join Date: May 2012
Location: Visalia CA
Posts: 118
|
Re: To all who keep asking on battery placement
Addition: i used wire wrap, wire loom, and heat tape to get my amperage ratings safe from insulative arch through
Posted via Mobile Device |
|
|
|
|
05-15-2012, 11:07 PM
|
#5 |
|
Registered User
Join Date: Mar 2012
Location: edgartown mass
Posts: 852
|
Re: To all who keep asking on battery placement
wire sizing is ok with me. (work on generators) was thinking about getting some double 00 to run. same thing they run on semis think i can get it cheap lol. i would do bat to starter on the pos and neg then starter to frame. and then frame back to bat. had to do that on my dads ss chevelle. worked well after that.
|
|
|
|
|
05-16-2012, 02:13 AM
|
#6 | |
|
Registered User
Join Date: May 2012
Location: Visalia CA
Posts: 118
|
Re: To all who keep asking on battery placement
Quote:
Charging the frame as a ground is proven to accelerate rust/corrosion. So if they salt the roads in mass id coat the frame at least. Just some thoughts! I think this will work well for you, handeling i noticed was loads better, took her to 115 and noticed the rear slumped in a better manner, calmed down like a dart. Also i highly reccomend an intruder switch on the container the batts will be in, mine has a dead man switch wired into the door sensor on alarm module so no one can just disconnect batt , shatter window, pop in nuteral and roll away. Hahha Posted via Mobile Device |
|
|
|
|
|
05-16-2012, 02:31 AM
|
#7 |
|
Registered User
Join Date: Jul 2009
Location: washington
Posts: 4,178
|
Re: To all who keep asking on battery placement
How long does it take to change a battery?? Lol
Posted via Mobile Device
__________________
377 sbc thumpr cam autogear m23 muncie 3:73 Detroit trutrac 3''spintech prostreet mufflers xpipe 1 3/4 headers build thread !http://67-72chevytrucks.com/vboard/s...d.php?t=577217 Iroc gauge threadhttp://67-72chevytrucks.com/vboard/s...d.php?t=554511 |
|
|
|
|
05-16-2012, 02:36 AM
|
#8 |
|
Registered User
Join Date: May 2012
Location: Visalia CA
Posts: 118
|
Re: To all who keep asking on battery placement
Givin water level is good, 2 seconds-10 hrs depending on amperage selected on charger. Always charge a dead batt with the lowest amperage, perferablely 5a at 13-14v. Monitor your batterys voltage CONSTANTLY. Should b about 12.80 v dc.
ALWAYS ADHEAR TO BATTERY CHARGERS MANUAL ALWAYS KEEP BAKING SODA NEAR AND FOLLOW PROPER SAFTEY TECHNIQUES. Acid burns are nasty, believe me. Baking soda saves lives. PERFORM AT YOUR OWN RISK Posted via Mobile Device |
|
|
|
|
| Bookmarks |
|
|
Hybrid Mode
