CA Blazer Hatch or parts

[Fesser]

I have a Blazer hatch that has some damage. The worst is a chunk taken out on the inside bottom edge near the center. Looks like it could easily be fixed and doesn't look like it would hurt the structural integrity. There appears to be a crack around the inside corner of the right side (viewing it with it laying on the ground interior side up) around the are where the latch mechanism is. Don't know how bad that might be. The whole thing appears to have been painted with latex paint so it is hard to tell. There are also a couple of cosmetic chips on the outside fiberglass. I don't see any cracks around the hinges. The latch handle is ugly with scratches and peeling in the cthrome. No key. Struts work properly as does the latch assembly. I will sell the whole hatch and the hardware shown (missing a couuple of the cover plate screws) for 225.00 plus shipping (almost certainly has to go Greyhound and I will have to crate it to some degree). This needs some work but is certainly not beyond repair.

Or... I will strip every piece of hardware off it, latches, rods, hinges (which are sloppy) struts, etc. and sell that for 120.00 shipped.

Obviously, if someone says they will take the hatch, then I won't be selling the hardware. If someone takes the hardware, what is left of the hatch might be for sale (depends a lot on what I have to do to get the hardware off).

Thanks, Frank (in Napa, CA)

[Fesser]

forgot to mention lots of little screw holes inside where they mounted curtain hardware and snaps.

[72K5NTX]

I would be interested in the handle and inside parts behind it. I dont need the rods or latches or any of that stuff. If you decide to part out, the handle (I assume it works) and the spring cam behind it is worth $40 to me.

[RideSF]

I'd like to pick up the hatch.. I live in san Francisco.. Pm sent
Posted via Mobile Device

[Fesser]

Originally Posted by 72K5NTX

I would be interested in the handle and inside parts behind it. I dont need the rods or latches or any of that stuff. If you decide to part out, the handle (I assume it works) and the spring cam behind it is worth $40 to me.

I don't know if you saw it but the handle is fairly ugly. There are scratches and the chrome has flaked off where you see the copper in the pictures. Also, I don't have the key for it. It was/is working fine though. Let me know if it is still worth it to you.

[RideSF]

I'm still interested n it.. I called u..
Posted via Mobile Device

[72K5NTX]

Yea still interested in the handle but I think RideSF is in line for the whole thing. If he needs the whole thing its prolly a better deal since the handle and cam behind it will be tough to pull out without sacrificing the hatch. Not sure where forum rules fall on this so...

[Fesser]

Guys, my screw up, went camping this weekend and didn't realize I had a call in my voicemail. I am not the best cell phone operator. If Nick is still in he's first. Nick, I no longer have your number in my phone. PM me or call me. Again, my apologies, Nick had called me but I missed it until I saw his post on here.

[RideSF]

Ok I'll give u a call
Posted via Mobile Device

[ZZ4]

Are any of these parts still available im interested in all the hardware?

[Fesser]

Originally Posted by ZZ4

Are any of these parts still available im interested in all the hardware?

Still available and would prefer to sell the complete hardware as a lot. PM sent to Z4

[Fesser]

Hatch sale pending.

[Fesser]

Hatch didn't sell so now it is just the hardware, I started to take it apart and decided it was easier to chop up the fibergalss leaving most of the hardware still bolted to the glass it was attached to. Some of the hardware is rusty and will take some penetrating oil to dismantle. One of the 1/4-20 bolts is missing from the support arm to hatch bracket.

I misplaced the two hinge covers and screws shown on the hatch glass in the pictures at the top of this post. If they are really needed I can remove the set on the hatch that I will be using.

Everything in the pictures of the parts on the white table is what I am selling.

$85.00 shipped without the two hinge covers, $100.00 shipped if I include my other set.

ZZ4 has first dibs on the hardware.

[Fesser]

more pictures...

[72K5NTX]

Handle is still worth $40 shipped to me so long as the spring and cam are in good shape. Could I get a couple pics of the back side of the handle?

[ZZ4]

Yea I do want it please...
Posted via Mobile Device

[houses28]

Ill take all of the hardware. I don't need the struts so would you sell all excluding the struts for $80 shipped

[briank]

Can I get in line for all the hardware?
Posted via Mobile Device

[Fesser]

Originally Posted by houses28

Ill take all of the hardware. I don't need the struts so would you sell all excluding the struts for $80 shipped

Houses 28 is up, and yes, I would do that, but you could always sell them for more than the difference I would think. Frank

[Fesser]

I want to give ZZ4 some more time to reply. I failed to answer one of his PM's when I was on vacation so I kind of owe him some time. Frank

[Fesser]

If I don't hear from ZZ4 by tomorrow morning, I will move on. Houses28 would be up next and then BrianK.

[Fesser]

Briank is up, if he wants to be. I had a few PM's on 8/3/12, and they will be up next after Brian.

[lolife99]

This is a hard thread to follow with all the Pm's going on.
What is left?
Everything off the hatch including the handle?
I might be interested.
Just need to know what is left for what price shipped.

[briank]

Fesser, I'll take it. Do you have all the original listed parts? Let me know how to pay you. Do you payal? Thanks!

[houses28]

this is house 28 you never pm me. I'm still interested. call me 214.766.2629