Disc brakes

[Mrcustom]

I was wondering does anyone make a master cylinder that I can use on my 57 under the frame. I bought the whole kit from CPP and the master has a power booster and will not fit under the frame where it should. exhaust & trans are in the way. I really don't want to put it in the engine compartment so i figure I would go with a non power booster for the front discs. Thanks for any help.

[mknittle]

There are guys here that mounted them farther back and made a linkage.

[Mrcustom]

Do you know who might have done this? So I can pick his brain..

[mknittle]

Originally Posted by Mrcustom

Do you know who might have done this? So I can pick his brain..

I will see if i can find the post.

[mknittle]

Originally Posted by Mrcustom

Do you know who might have done this? So I can pick his brain..

Kim did one.A nice job too!
post 200 shows the set up together.

http://67-72chevytrucks.com/vboard/s...=283107&page=8

[Amorget]

Another option you have is a hydroboost unit. They are much smaller then their vacuum counterparts.

[mr48chev]

I can't remember who's build thread it is on but there are a couple of trucks with the mastercylinder & booster mounted a ways back on the frame with long (and stout) push rods to work them.

If you are running power steering to begin with the hydro boost suggestion is a good one as they don't take up as much room and have a great feel as far as pedal.

[mknittle]

Originally Posted by mr48chev

I can't remember who's build thread it is on but there are a couple of trucks with the mastercylinder & booster mounted a ways back on the frame with long (and stout) push rods to work them.

If you are running power steering to begin with the hydro boost suggestion is a good one as they don't take up as much room and have a great feel as far as pedal.

Wasn't there a thread on that a while back? I think I remember seberal pics in the same place. I just cant find it.

[parkwood]

Originally Posted by Mrcustom

I was wondering does anyone make a master cylinder that I can use on my 57 under the frame. I bought the whole kit from CPP and the master has a power booster and will not fit under the frame where it should. exhaust & trans are in the way. I really don't want to put it in the engine compartment so i figure I would go with a non power booster for the front discs. Thanks for any help.

This is in a '56 chevy and as you can see it clears everything great.. It's from TCI. hope this helps..

[Mrcustom]

How does you exhaust clear the master?

[1project2many]

Looks like you have to install a trap door to access the master cylinder cover pictured above? There are late model masters which use a single point twist cover and might be fitted so they can be filled through the original access hole. 99+ S10 is one application that I can think of.


Hydroboost is ok. I've installed one in my '95 Blazer. One warning is that all hydroboost master cylinders (at least for GM) have the same size bore and it's pretty large. The pedal applies really high, but the brake effort can end up higher than expected.

[G&R's57GMC]

Originally Posted by 1project2many

Looks like you have to install a trap door to access the master cylinder cover pictured above?

Or you could install a remote reservoir.
Found this at http://www.fillingstation.com part # RR-47

[parkwood]

Originally Posted by G&R's57GMC

Or you could install a remote reservoir.
Found this at http://www.fillingstation.com part # RR-47

Yes that would be a cool extra...

[oldcouple]

Originally Posted by G&R's57GMC

Or you could install a remote reservoir.
Found this at http://www.fillingstation.com part # RR-47

That looks alot like a early VW bug remote, which is what I have been using, you have to drill a tap the MC to attach the lines.

[parkwood]

Originally Posted by Mrcustom

How does you exhaust clear the master?

Hope these help... and i never have to cut a hole in the floor to add fluid..it's clears the bottom of the floor so you can put in fluid using a squeeze bottle

[_Ogre]

i just posted this in another brake thread, look in my build thread if you need more pics.
i like the hydroboost for it's stopping power with my weak legs.
if you use the mustang hydroboost you can install a remote reservoir from a nissan quest.

look at orrieg's build he moved the mc back to clear other obstacles too. look at his build for more ideas.

Originally Posted by _Ogre

i use an 03 mustang hydroboost on my 58, it has power to stop a mack truck
you can buy a mount to put a power steering pump anywhere on the front of a sbc
i mounted the hydroboost in the stock location, the power steering pump low on the drivers side and have a remote reservoir








i made my own pump mount with 3/8'' id tube and flat plate. no welding.

[azsnow]

I have the same kit from CPP, and don't have any issues with clearance either, so I am not sure what probs you are having, can you post some pics? I know you must use a different trans crossmember other then the stocker, and I have headmen hedders and just ran the exhaustt as shown in the previous pics.

[_Ogre]

the frame on a tf truck is very high above the rockers
the exhaust on these trucks hangs under the frame
any brake upgrade will be in the frame
lots of room under these trucks

and even if you have to modify the exhaust
if you can't handle an exhaust modification
you probably shouldn't be working on a brake modification

[Mrcustom]

You are a funny guy!!!!