|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
04-27-2013, 07:54 AM
|
#1 |
|
Registered User
Join Date: Dec 2010
Location: konawa ok/oakdale Ca.
Posts: 1,652
|
Can i use this trans crossmember?
Im getting ready to drop the engine and trans in my 66.Ive searched the other threads and every body uses the crossmember that bolts into the frame from inside on both sides.Mine just just has the bolts like this on one side then the other side bolts on the outside of the frame.Can I still use this?I also noticed on the frame there is some holes that look like they were there for the transmission if the truck had been an automatic.Did the factory put theses holes for an automatic?Can I use them or am I better off drlling my own holes?
|
|
|
|
04-27-2013, 07:58 AM
|
#2 |
|
Registered User
Join Date: Dec 2010
Location: konawa ok/oakdale Ca.
Posts: 1,652
|
Re: Can i use this trans crossmember?
|
|
|
|
|
04-27-2013, 09:08 AM
|
#3 |
|
Registered User
Join Date: Sep 2010
Location: Winchester Oregon, formerly Vancouver BC
Posts: 2,949
|
Re: Can i use this trans crossmember?
I have never seen anything like that for a crossmember.
|
|
|
|
|
04-27-2013, 11:40 AM
|
#4 | |
|
Registered User
Join Date: Feb 2008
Location: Sidney,b.c.
Posts: 4,425
|
Re: Can i use this trans crossmember?
Quote:
http://www.persh.org/pickup/700R4.htm I do have a stock a/t crossmember avail ron |
|
|
|
|
|
04-27-2013, 02:29 PM
|
#5 |
|
Registered User
Join Date: Aug 2002
Location: Westbank, BC
Posts: 403
|
Re: Can i use this trans crossmember?
I looked at the CPP crossmember, but decided to build my own. I bought a 3' stick of 1.25 square tubing and some angle iron for the frame mounts and trans mount.
Cost me $30 for steel. I would just buy the CPP unit for $75 shipped off EBay if I lived in the States. Costs too much crossing the border  Posted via Mobile Device
__________________
1965 Chevy Short Box Stepside, 230 - 3 speed, 4:11 gears, original paint rust free survivor. Now sporting a 383 SBC and TKO-600 |
|
|
|
|
04-27-2013, 09:55 AM
|
#6 |
|
Registered User
Join Date: Dec 2010
Location: konawa ok/oakdale Ca.
Posts: 1,652
|
Re: Can i use this trans crossmember?
The one I have is the old stock one in the pic.I stole the pic from another thread.I think he modified it for 80's style square body.I guess this kind of crossmember was used in chevys low powered smog engines.Im putting a 305 in my 66.I just want to make shure im not wasting my time using this.I havnt seen any body else using this cross member on here on one of our trucks.
|
|
|
|
|
04-27-2013, 10:01 AM
|
#7 |
|
Registered User
Join Date: Sep 2010
Location: Winchester Oregon, formerly Vancouver BC
Posts: 2,949
|
Re: Can i use this trans crossmember?
I used an ECE crossmember for my suburban, I would try to find a stock one or use a CPP or ECE one. The holes are in the frame for the auto already so you don't need to drill new holes.
|
|
|
|
|
04-27-2013, 10:16 AM
|
#8 |
|
Registered User
Join Date: Dec 2010
Location: konawa ok/oakdale Ca.
Posts: 1,652
|
Re: Can i use this trans crossmember?
I think i will end up doing that LT1 Burb.From what the square body guys say this crossmember weakens your frame and its hard to route your exhaust.
|
|
|
|
|
04-27-2013, 11:11 AM
|
#9 |
|
Registered User
 
Join Date: Sep 2006
Location: San Francisco
Posts: 4,782
|
Re: Can i use this trans crossmember?
I used the stock automatic trans crossmembers in my trucks.
__________________
"A man and his truck, what a beautiful thing" 65 Short Fleetside BBC 65 Long Fleetside 283 3 on the tree for now. my build thread http://www.67-72chevytrucks.com/vboa...d.php?t=259536 |
|
|
|
|
| Bookmarks |
|
|
Hybrid Mode
